Curvature of surfaces

To measure the curvature of a surface at a point, Euler, in 1760, looked at cross sections of the surface made by planes that contain the line perpendicular (or “normal”) to the surface at the point (see figure). Euler called the curvatures of these cross sections the normal curvatures of the surface at the point. For example, on a right cylinder of radius r, the vertical cross sections are straight lines and thus have zero curvature; the horizontal cross sections are circles, which have curvature 1/r. The normal curvatures at a point on a surface are generally different in different directions. The maximum and minimum normal curvatures at a point on a surface are called the principal (normal) curvatures, and the directions in which these normal curvatures occur are called the principal directions. Euler proved that for most surfaces where the normal curvatures are not constant (for example, the cylinder), these principal directions are perpendicular to each other. (Note that on a sphere all the normal curvatures are the same and thus all are principal curvatures.) These principal normal curvatures are a measure of how “curvy” the surface is.

The theory of surfaces and principal normal curvatures was extensively developed by French geometers led by Gaspard Monge (1746–1818). It was in an 1827 paper, however, that the German mathematician Carl Friedrich Gauss made the big breakthrough that allowed differential geometry to answer the question raised above of whether the annular strip is isometric to the strake. The Gaussian curvature of a surface at a point is defined as the product of the two principal normal curvatures; it is said to be positive if the principal normal curvatures curve in the same direction and negative if they curve in opposite directions. Normal curvatures for a plane surface are all zero, and thus the Gaussian curvature of a plane is zero. For a cylinder of radius r, the minimum normal curvature is zero (along the vertical straight lines), and the maximum is 1/r (along the horizontal circles). Thus, the Gaussian curvature of a cylinder is also zero.

If the cylinder is cut along one of the vertical straight lines, the resulting surface can be flattened (without stretching) onto a rectangle. In differential geometry, it is said that the plane and cylinder are locally isometric. These are special cases of two important theorems:

• Gauss’s “Remarkable Theorem” (1827). If two smooth surfaces are isometric, then the two surfaces have the same Gaussian curvature at corresponding points. (Athough defined extrinsically, Gaussian curvature is an intrinsic notion.)
• Minding’s theorem (1839). Two smooth (“cornerless”) surfaces with the same constant Gaussian curvature are locally isometric.

As corollaries to these theorems:

• A surface with constant positive Gaussian curvature c has locally the same intrinsic geometry as a sphere of radius Square root of√1/c. (This is because a sphere of radius r has Gaussian curvature 1/r²).
• A surface with constant zero Gaussian curvature has locally the same intrinsic geometry as a plane. (Such surfaces are called developable).
• A surface with constant negative Gaussian curvature c has locally the same intrinsic geometry as a hyperbolic plane. (See non-Euclidean geometry.)

The Gaussian curvature of an annular strip (being in the plane) is constantly zero. So to answer whether or not the annular strip is isometric to the strake, one needs only to check whether a strake has constant zero Gaussian curvature. The Gaussian curvature of a strake is actually negative, hence the annular strip must be stretched—although this can be minimized by narrowing the shapes.

Shortest paths on a surface

From an outside, or extrinsic, perspective, no curve on a sphere is straight. Nevertheless, the great circles are intrinsically straight—an ant crawling along a great circle does not turn or curve with respect to the surface. About 1830 the Estonian mathematician Ferdinand Minding defined a curve on a surface to be a geodesic if it is intrinsically straight—that is, if there is no identifiable curvature from within the surface. A major task of differential geometry is to determine the geodesics on a surface. The great circles are the geodesics on a sphere.

A great circle arc that is longer than a half circle is intrinsically straight on the sphere, but it is not the shortest distance between its endpoints. On the other hand, the shortest path in a surface is not always straight, as shown in the figure. An important theorem is:

On a surface which is complete (every geodesic can be extended indefinitely) and smooth, every shortest curve is intrinsically straight and every intrinsically straight curve is the shortest curve between nearby points.