Isolation and preconcentration

In many modern analytical procedures, once the test portion has been dissolved, it is diluted to some fixed volume and measured. However, this is not always the case. Sometimes it is necessary to remove or mask interferences, perhaps even to completely isolate the intended analyte from its sample matrix and dissolution medium.

Many isolation techniques involve the use of heat to change the analyte into a gaseous species and are conveniently referred to as thermal evolution techniques. For inorganic analytes it is possible to distinguish those that can sometimes be isolated directly from the undissolved test portion. This category includes the instrumental methods that use reactive gases and those that use inert gases. The most common reactive gas is oxygen, which is used to convert carbon to carbon monoxide and sulfur to sulfur dioxide as the test portion is rapidly heated in either a resistance or an induction furnace. Noble gases, such as helium and argon, are commonly used as carriers to transport nitrogen, oxygen, and hydrogen from the test portion as it is rapidly heated.

The distillation of inorganic elements from an aqueous solution is applicable to a number of different species, both for the removal of interferences and for the collection of analytes. The volatilization of interferences can be accomplished from a beaker on a hot plate. The distillation and isolation of volatile analytes, however, requires a special enclosed apparatus, which usually includes a water-cooled condenser.

In organic work, thermal evolution techniques include fractional distillation and gas chromatography. In the former, careful temperature control allows the collection of constant-boiling species from simple mixtures.

In general, gas chromatography allows much higher resolution separations and is widely used in both preparation and analysis. Analytical gas chromatography is normally a combined separation and measurement approach. There are also methods that use a “pre-column” to remove the bulk of the sample matrix while passing the analyte components onto a separating column. For example, in headspace analysis the equilibrated atmosphere above the surface of a liquid is sampled and injected into a gas chromatograph. It is a thermal evolution method in the sense that the distribution of analyte between the liquid and gas phases is temperature dependent.

Solvent extraction is another isolation technique widely used in both inorganic and organic analysis. When two immiscible or partially miscible solvents are agitated together, a dissolved chemical species may preferentially migrate to one of the two liquid phases. Use of this phenomenon is practical only for electrically neutral species. One of the two solvents is usually water.

It is also often critical that the analyte be adjusted to a specific oxidation state prior to extraction. Similarly, it may be necessary to adjust the oxidation state of a potential interferent to ensure that it is not extracted. Masking agents are frequently added to convert interferents to nonextractable species.

Ion exchange can also be used to isolate the analyte. It is most frequently applied as a form of column chromatography in which ions in a (usually aqueous) solution passed through a resin-packed glass column switch places with ions bound on ion-exchange resin beads. Ion-exchange separations are based on the fact that different ions will have different affinities for the resin. Thus, an ion with lower affinity will be displaced by an ion of greater affinity. The displaced ion is then washed off the column and perhaps collected. Often most of the sample matrix ions are initially bound to the resin, and then each type of ion is selectively removed by washing the column with various electrolytes.

A common means of partially or completely isolating the analyte is the precipitation reaction, which requires the formation of a low-solubility, easily filterable product. Complete precipitation of the analyte may require the addition of a “carrier” species that “co-precipitates” with the analyte under the same reaction conditions. The carrier is chosen to have no effect in subsequent manipulations with the analyte. Sometimes, however, co-precipitation occurs with an interferent element from the sample matrix. In this case some chemical strategy must be applied to avoid co-precipitation.

Sometimes the analyte precipitates in such finely divided form that it is impossible to filter by ordinary means. In this case warming, boiling, or adding reagents may be necessary to agglomerate the analyte to filterable size. The quantitative transfer of a precipitate to a filter is a manipulative art that becomes more critical at higher analyte concentrations.

Masking

Sometimes it is not necessary to isolate the analyte chemically in order to deal with interferences. Masking agents are additives that undergo some reaction in the sample solution that complexes (or precipitates) potential interfering elements and converts them to a form that does not interfere with subsequent analyte manipulation or measurement. Masking agents are used in molecular absorption spectrophotometry, gravimetry, titrimetry, and voltammetry.

In a larger sense, any additive that facilitates the analytical process by removing some impediment to an accurate measurement may be considered a masking agent. Matrix modifiers are substances added to prevent analyte loss and volatilize away interferences during the char cycle of electrothermal atomic absorption measurement. Ionization suppressors are additives that are readily ionized in flame atomic absorption measurement; they reduce the ionization of the analyte and thus enhance sensitivity. Commonly used ionization suppressors are lanthanum, sodium, and strontium compounds.