In most passenger cars through the middle of the 20th century, a pressed-steel frame—the vehicle’s chassis—formed a skeleton on which the engine, wheels, axle assemblies, transmission, steering mechanism, brakes, and suspension members were mounted. The body was flexibly bolted to the chassis during a manufacturing process typically referred to as body-on-frame construction. This process is used today for heavy-duty vehicles, such as trucks, which benefit from having a strong central frame, subjected to the forces involved in such activities as carrying freight, including the absorption of the movements of the engine and axle that is allowed by the combination of body and frame.

In modern passenger-car designs, the chassis frame and the body are combined into a single structural element. In this arrangement, called unit-body (or unibody) construction, the steel body shell is reinforced with braces that make it rigid enough to resist the forces that are applied to it. Separate frames or partial “stub” frames have been used for some cars to achieve better noise-isolation characteristics. The heavier-gauge steel present in modern component designs also tends to absorb energy during impacts and limit intrusion in accidents.

Engine

1 of 2

2 of 2

A wide range of engines has been used experimentally and in automotive production. The most successful for automobiles has been the gasoline-fueled reciprocating-piston internal-combustion engine, operating on a four-stroke cycle, while diesel engines are widely used for trucks and buses. The gasoline engine was originally selected for automobiles because it could operate more flexibly over a wide range of speeds, and the power developed for a given weight engine was reasonable; it could be produced by economical mass-production methods; and it used a readily available, moderately priced fuel. Reliability, compact size, exhaust emissions, and range of operation later became important factors.

There has been an ongoing reassessment of these priorities with new emphasis on the reduction of greenhouse gases (see greenhouse effect) or pollution-producing characteristics of automotive power systems. This has created new interest in alternate power sources and internal-combustion engine refinements that previously were not close to being economically feasible. Several limited-production battery-powered electric vehicles are marketed today. In the past they had not proved to be competitive, because of costs and operating characteristics. The gasoline engine, with new emission-control devices to improve emission performance, has been challenged in recent years by hybrid power systems that combine gasoline or diesel engines with battery systems and electric motors. Such designs are, however, more complex and therefore more costly.

The evolution of higher-performance engines in the United States led the industry away from long, straight engine cylinder layouts to compact six- and eight-cylinder V-type layouts for larger cars (with horsepower ratings up to about 350). Smaller cars depend on smaller four-cylinder engines. European automobile engines were of a much wider variety, ranging from 1 to 12 cylinders, with corresponding differences in overall size, weight, piston displacement, and cylinder bores. A majority of the models had four cylinders and horsepower ratings up to 120. Most engines had straight or in-line cylinders. There were, however, several V-type models and horizontally opposed two- and four-cylinder makes. Overhead camshafts were frequently employed. The smaller engines were commonly air-cooled and located at the rear of the vehicle; compression ratios were relatively low. Increased interest in improved fuel economy brought a return to smaller V-6 and four-cylinder layouts, with as many as five valves per cylinder to improve efficiency. Variable valve timing to improve performance and lower emissions has been achieved by manufacturers in all parts of the world. Electronic controls automatically select the better of two profiles on the same cam for higher efficiency when engine speeds and loads change.

Fuel

Specially formulated gasoline is essentially the only fuel used for automobile operation, although diesel fuels are used for many trucks and buses and a few automobiles, and compressed liquefied hydrogen has been used experimentally. The most important requirements of a fuel for automobile use are proper volatility, sufficient antiknock quality, and freedom from polluting by-products of combustion. The volatility is reformulated seasonally by refiners so that sufficient gasoline vaporizes, even in extremely cold weather, to permit easy engine starting. Antiknock quality is rated by the octane number of the gasoline. The octane number requirement of an automobile engine depends primarily on the compression ratio of the engine but is also affected by combustion-chamber design, the maintenance condition of engine systems, and chamber-wall deposits. In the 21st century regular gasoline carried an octane rating of 87 and high-test in the neighbourhood of 93.

Automobile manufacturers have lobbied for regulations that require the refinement of cleaner-burning gasolines, which permit emission-control devices to work at higher efficiencies. Such gasoline was first available at some service stations in California, and from 2017 the primary importers and refiners of gasoline throughout the United States were required to remove sulfur particles from fuel to an average level of 10 parts per million (ppm).

Vehicle fleets fueled by natural gas have been in operation for several years. Carbon monoxide and particulate emissions are reduced by 65 to 90 percent. Natural-gas fuel tanks must be four times larger than gasoline tanks for equivalent vehicles to have the same driving range. This compromises cargo capacity.

Ethanol (ethyl alcohol) is often blended with gasoline (15 parts to 85 parts) to raise its octane rating, which results in a smoother-running engine. Ethanol, however, has a lower energy density than gasoline, which results in decreased range per tankful.

Lubrication

All moving parts of an automobile require lubrication. Without it, friction would increase power consumption and damage the parts. The lubricant also serves as a coolant, a noise-reducing cushion, and a sealant between engine piston rings and cylinder walls. The engine lubrication system incorporates a gear-type pump that delivers filtered oil under pressure to a system of drilled passages leading to various bearings. Oil spray also lubricates the cams and valve lifters.

Wheel bearings and universal joints require a fairly stiff grease; other chassis joints require a soft grease that can be injected by pressure guns. Hydraulic transmissions require a special grade of light hydraulic fluid, and manually shifted transmissions use a heavier gear oil similar to that for rear axles to resist heavy loads on the gear teeth. Gears and bearings in lightly loaded components, such as generators and window regulators, are fabricated from self-lubricating plastic materials. Hydraulic fluid is also used in other vehicle systems in conjunction with small electric pumps and motors.