A helicopter has four controls: collective pitch control, throttle control, antitorque control, and cyclic pitch control.

The collective pitch control is usually found at the pilot’s left hand; it is a lever that moves up and down to change the pitch angle of the main rotor blades. Raising or lowering the pitch control increases or decreases the pitch angle on all blades by the same amount. An increase in the pitch angle will increase the angle of attack, causing both lift and drag to increase and causing the rpm of the rotor and the engine to decrease. The reverse happens with a decrease in pitch angle.

Because it is necessary to keep rotor rpm as constant as possible, the collective pitch control is linked to the throttle to automatically increase power when the pitch lever is raised and decrease it when the pitch lever is lowered. The collective pitch control thus acts as the primary control both for altitude and for power.

The throttle control is used in conjunction with the collective pitch control and is an integral part of its assembly. The throttle control is twisted outboard to increase rotor rpm and inboard to decrease rpm.

The antitorque controls are pedals linked to operate a pitch change mechanism in the tail rotor gearbox. A change in pedal position changes the pitch angle of the tail rotor to offset torque. As torque varies with every change of flight condition, the pilot is required to change pedal position accordingly. The antitorque control does not control the direction of flight.

More From Britannica

aerospace industry: Helicopters

It was stated above that the lift/thrust force is always perpendicular to the plane of rotation of the rotor. The cyclic pitch control, a stick-type control found to the pilot’s right, controls the direction of flight by tipping the plane of rotation in the desired direction. The term cyclic derives from the sequential way each blade’s pitch is changed so that it takes the flight path necessary to effect the change in direction.

Differences in helicopter and airplane design and construction

The most immediate and obvious difference in the construction of a fixed-wing aircraft and a helicopter is of course the latter’s use of a rotor instead of a wing. There are many other critical additions, however, including the use of a tail rotor to offset torque. (Some helicopters use a “no tail rotor” system, in which low-pressure air is circulated through a tail boom to control the torque of the spinning main rotor.) Less obvious are such additions as the transmission system, which is used to transfer power from the engine to the rotor, tail rotor, and other accessories; the clutch, used to engage the engine and transmission with the rotor; and the mechanics of the rotor system itself.

The first helicopters were quite primitive, with skids instead of wheeled landing gear, open cockpits, and unaired fuselage sections. Helicopters are now as fully equipped as airplanes, with retractable landing gear and full instrumentation and navigation equipment, and are provided with whatever accoutrements may be necessary to accomplish the specific task at hand. For example, some helicopters are flying ambulances, especially equipped with a complete set of intensive-care accessories. Others function as electronic news gatherers, with appropriate sensors and telecommunications equipment.

The design and operation of helicopters have derived the same advances from computers and composites as have other aircraft, especially in the design and construction of the rotor blades. One of the more important improvements is in the simplification of flight-control systems, where a simple side stick controller, with the assistance of computers, performs the functions of the collective, cyclic, and throttle controls.

Helicopter designs have included a number of optional rotor configurations, such as rotors that stop to serve as a fixed wing for forward flight; rotors that fold in a streamwise direction to blend in with, or be stowed within, the fuselage contours, lift being provided by a stub wing; and X-shaped rotors that rotate for takeoff and landing but are fixed for lift in flight.

In sum, the additional forces imposed upon a helicopter by its very concept delayed its development, made it relatively more difficult to control than fixed-wing aircraft, and, in general, impeded its use. While generally considered more expensive to operate than conventional fixed-wing aircraft, a true comparison of costs cannot be made without assessing the additional advantages conferred by the vertical flight capability. The popularity of the helicopter indicates that users willingly pay any additional costs involved to obtain that capability. In some applications—medical evacuation, supplying of oil drilling rigs, spreading of certain agricultural agents, to name but a few—it is irreplaceable.