Modifications of basic machines
Certain machine tools have been designed to speed up production. Although these tools include features of the basic machine tools and perform the same operations, they incorporate design modifications that permit them to perform complex or repetitive operational sequences more rapidly. Furthermore, after the production machine has been set up by a skilled worker or machinist, a less skilled operator also can produce parts accurately and rapidly. The following are examples of production machine tools that are modifications of basic machine tools: (1) turret lathes, including screw machines; (2) multiple-station machines; (3) gang drills; and (4) production milling machines.
Turret lathes
Horizontal turret lathes have two features that distinguish them from engine lathes. The first is a multiple-sided main turret, which takes the place of the tailstock on the engine lathe. A variety of turning, drilling, boring, reaming, and thread-cutting tools can be fastened to the main turret, which can be rotated intermittently about its vertical axis with a hand wheel. Either a hand wheel or a power feed can be used to move the turret longitudinally against the workpiece mounted on the machine spindle.
The second distinguishing feature of the turret lathe is the square turret mounted on the cross slide. This turret also can be rotated about its vertical axis and permits the use of a variety of turning tools. A tool post, or tool block, can be clamped to the rear of the cross slide for mounting additional tools. The cross slide can be actuated either by hand or by power.
Turret lathes may be classified as either bar machines or chucking machines. Bar machines formerly were called screw machines, and they may be either hand controlled or automatic. A bar machine is designed for machining small threaded parts, bushings, and other small parts that can be created from bar stock fed through the machine spindle. Automatic bar machines produce parts continuously by automatically replacing of bar stock into the machine spindle. A chucking machine is designed primarily for machining larger parts, such as castings, forgings, or blanks of stock that usually must be mounted in the chuck manually.
Multiple-station machines
Several types of multiple-station vertical lathes have been developed. These machines are essentially chucking-type turret lathes for machining threaded cylindrical parts. The machine has 12 spindles, each equipped with a chuck. Directly above each spindle, except one, tooling is mounted on a ram. Parts are mounted in each chuck and indexed for up to 11 machining operations. The finished part is removed at the 12th station.
Gang drills
A gang-drilling machine consists of several individual columns, drilling heads, and spindles mounted on a single base and utilizing a common table. Various numbers of spindles may be used, but four or six are common. These machines are designed for machining parts requiring several hole-machining operations, such as drilling, countersinking, counterboring, or tapping. The workpiece is moved from one drilling spindle to the next, where sequential machining operations are performed by one or more operators.
Production millers
Milling machines used for repet-itive-production milling operations generally are classified as bed-type milling machines because of their design. The sliding table is mounted directly onto the massive bed of the machine and cannot be raised or moved transversely; table movement is longitudinal only. The spindle head may be adjusted vertically to establish the depth of cut. Some machines are equipped with automatic controls that require only a semiskilled operator to load parts in fixtures at each end of the table and start the machine. One part can be unloaded and replaced while the other is being machined.
Special-purpose machines
Special-purpose machine tools are designed to perform special machining operations, usually for production purposes. Examples include gear-cutting and gear-grinding machines, broaching machines, lapping and honing machines, and boring machines.
Gear-cutting machines
Three basic cutting methods are used for machining gears: (1) form cutting, (2) template cutting, and (3) generating. The form-cutting method uses a cutting tool that has the same form as the space between two adjacent teeth on a gear. This method is used for cutting gear teeth on a milling machine. The template-cutting method uses a template to guide a single-point cutter on large bevel-gear cutting machines.
Most cut gears produced in large lots are made on machines that utilize the gear-generating method. This method is based on the principle that two involute gears, or a gear and rack, with the same diametral pitch will mesh together properly. Therefore, a cutting tool with the shape of a gear or rack may be used to cut gear teeth in a gear or rack blank. This principle is applied in the design of a number of widely used gear-cutting machines of the generating type. Gear-generating machines that cut with reciprocating strokes are called gear shapers.
Gear-hobbing machines use a rotating, multiple-tooth cutting tool called a hob for generating teeth on spur gears, worm gears, helical gears, splines, and sprockets. More gears are cut by hobbing than by other methods because the hobbing cutter cuts continuously and produces accurate gears at high production rates. In gear-making machines gears can be produced by cutting, grinding, or a combination of cutting and grinding operations.
Broaching machines
In general, broaching is classified as a planing or shaping art because the action of a broaching tool resembles the action of planer and shaper tools. Broaching tools of various designs are available. The teeth on broaching tools are equally spaced, with each successive tooth designed to feed deeper into the workpiece, thus completing the broaching operation in a single stroke. Examples of internal broaching applications include cutting keyways in the hubs of gears or pulleys, cutting square or hexagonal holes, and cutting gear teeth. External grooves can be cut in a shaft with an external broaching tool. Some broaching machines pull or push broaching tools through or over the workpiece.
Lapping and honing machines
Lapping and honing operations are classified under the basic art of grinding. Lapping is a process in which a soft cloth impregnated with abrasive pastes or compounds is rubbed against the surface of a workpiece. Lapping is used to produce a high-quality surface finish or to finish a workpiece within close size limits. Dimensional tolerances of two millionths of an inch (0.00005 millimetre) can be achieved in the hand or machine lapping of precision parts such as gauges or gauge blocks.
Honing is a low-speed surface finishing process used for removing scratches, machine marks, or small amounts of metal, usually less than 0.0005 inch (0.0125 millimetre), from ground or machined surfaces. Honing is done with bonded abrasive sticks or stones that are mounted in a honing head. In a typical honing operation, such as honing automotive engine cylinder walls, a honing machine with one or more spindles is used. The honing head rotates slowly with an oscillating motion, holding the abrasive sticks against the work surface under controlled light pressure.