- Related Topics:
- film
- technology
The final combination of tracks onto one composite sound track synchronous with the picture is variously known as mixing, rerecording, or dubbing. Mixing takes place at a special console equipped with separate controls for each track to adjust loudness and various aspects of sound quality. Although some of the new digital processes employ the record-industry technique of overdubbing, or building sound track-by-track onto a single tape, most mixing in films is still performed by the traditional practice of threading multiple dubbing units (sprocketed magnetic film containing separate music, dialogue, and sound effects elements) on banks of interlocked dubbers. The playback dubbers are connected by selsyn motors to one another, as well as to the rerecorders that produce the master, or parallel music/dialogue/effects (M/D/E), track on full-coat magnetic stock. Also in interlock are a projector that allows the mixer to work from the actual image and a footage counter that allows the mixer to follow cue sheets, or logs, which indicate by footage number when each track should be brought in and out.
The mixer strives to strike the right dramatic balance between dialogue, music, and effects and to avoid monotony. Mixing procedures vary widely. Some studios use one mixer for each of the three main tracks, in which case the effects tracks have probably been mixed down earlier onto one combined track. In the early days of magnetic recording, stopping the rerecording equipment produced an audible click on the track; if a mistake were made, mixing would have to be redone from the beginning of the tape reel. The advent of back-up recording in the 1960s eliminated the click, making it possible for mixers to work on smaller segments and to correct mistakes without starting over. This enables the mix to be controlled by one person, who may be combining as many as 24 tracks. An even greater advance is the computerized console that enables the mixer to go back and correct any one track without having to remix the others.
For monaural release, a composite music/dialogue/effects master on full-coat 35-mm magnetic film is converted to an optical sound negative. For stereo, four-track submasters for M/D/E are mixed down to a two-track magnetic matrix encoded to contain four channels of sound information. Optical sound negatives are copied from the magnetic master, and they are then composited with the picture internegative so that they are in projection sync (on 35-mm prints the sound is placed 21 frames in advance of its corresponding image; on 16-mm prints the sound is 26 frames in advance of the picture).
Because of narrow track width, optical stereo sound tracks require a system of noise reduction such as Dolby Type A. The Dolby system works by responding to changing amplitudes in various regions of the frequency spectrum of an audio signal. The quieter passages are boosted to increase the spread between the signal (desired sound) and the unwanted ground noise. When played back, normal levels are restored, and the ground noise drops below the threshold of audibility.
Projection technology and theater design
Projectors. The projector is the piece of motion-picture equipment that has changed the least. Manufacturers produce models virtually identical to those of the 1950s, and even the 1930 model Super Simplex is still in wide use. The essential mechanism is still the four-slot Maltese cross introduced in the 1890s. The Maltese cross provides the intermittent Geneva movement that stops each frame of the continuously moving film in front of the picture aperture, where it can be projected (or, in a camera, exposed). The movement starts with a continuously rotating gear and cam (see , left). Each 360-degree rotation of the gear and cam causes a pin to engage one of the slots of the Maltese cross. The pin rotates the cross, which in turn rotates a shaft, one quarter turn. As the shaft rotates, four of the 16 teeth on the intermittent sprocket advance and engage the perforations (sprocket holes) on one frame of the film. The sprocket moves only when the pin is fully engaged in the Maltese cross slot (see , right). This is the “pull-down” phase; in the other phases the curved surfaces of the cam and the cross are in contact and the movement is in the “dwell” position. The Geneva movement is also called a 3:1 movement because there are three quarter-cycles of dwell for every one quarter-cycle of pull-down.
Sound, unlike images, cannot be reproduced intermittently; sound must be continuous to be realistic. The optical-sound-reading equipment on a projector is therefore located below the picture aperture (see ), and the sound on an optical 35-mm print is located 21 frames ahead of its corresponding image. A light beam (supplied by a direct current for stability) is shone through a rectangular slit and focused by a lens to dimensions of .001 by .084 inch onto the sound track. The sound track’s varying bands of light and dark then modulate the amount of light from the beam that is allowed to pass to the optical pickup. In older equipment this pickup was a photoelectric cell that changed electrical resistance under exposure to light. Newer designs employ a solar cell of photovoltaic material to convert light energy to electric energy.
An important element of picture quality on the screen is brightness. For decades the standard light source was the carbon-arc lamphouse, which used disposable electrodes (positive and negative carbon-clad rods) that would be moved together as they burned; the rods needed to be replaced every hour or so. Xenon lamps were introduced in West Germany in the 1950s, and carbon-arc projection is now found only in older theaters. Both carbon-arc and xenon lamps are run off a direct-current power supply in order to minimize brightness variations due to fluctuations in voltage. The xenon bulb replaces the positive and negative carbons with a tungsten anode and cathode in a quartz envelope filled with xenon gas under pressure. Light from xenon bulbs has a color temperature closer to that of daylight than carbon-arc light does; that is, it is bluer and is therefore particularly well suited to color films.