Passive detectors
- Related Topics:
- radiation
- measurement
- nuclear physics
Photographic emulsions
The use of photographic techniques to record ionizing radiations dates back to the discovery of X rays by Röntgen in the late 1800s, but similar techniques remain important today in some applications. A photographic emulsion consists of a suspension of silver halide grains in an inert gelatin matrix and supported by a backing of plastic film or another material. If a charged particle or fast electron passes through the emulsion, interactions with silver halide molecules produce a similar effect as seen with exposure to visible light. Some molecules are excited and will remain in this state for an indefinite period of time. After the exposure is completed, this latent record of the accumulated exposure can be made visible through the chemical development process. Each grain containing an excited molecule is converted to metallic silver, greatly amplifying the number of affected molecules to the point that the developed grain is visible. Photographic emulsions used for radiation detection purposes can be classified into two main subgroups: radiographic films and nuclear emulsions. Radiographic films register the results of exposure to radiation as a general darkening of the film due to the cumulative effect of many radiation interactions in a given area of the emulsion. Nuclear emulsions are intended to record individual tracks of a single charged particle.
Radiographic films
Radiographic films are most familiar in their application in medical X-ray imaging. Their properties do not differ drastically from those of normal photographic film used to record visible light, except for an unusually high silver halide concentration. Thickness of the emulsion ranges from 10 to 20 micrometres, and they contain silver halide grains up to 1 micrometre in diameter. The probability that a typical incident X ray will interact in the emulsion is only a few percent, and so methods are often applied to increase the sensitivity so as to reduce the intensity of the X rays needed to produce a visible image. One such technique is to apply emulsion to both sides of the film base. Another is to sandwich the photographic emulsion between intensifier screens that consist of thin layers of light-emitting phosphors of high atomic number, such as calcium tungstate, cesium iodide, or rare earth phosphors. If an X ray interacts in the screen, the light that is produced darkens the film in the immediate vicinity through the normal photographic process. Because of the high atomic number of the screens, they are more likely to cause an X ray to interact than the emulsion itself, and the X-ray flux needed to achieve a given degree of darkening of the emulsion can be decreased by as much as an order of magnitude. The light is produced in the normal scintillation process (see below Active detectors: Scintillation and Čerenkov detectors) and travels in all directions from the point of the X-ray interaction. This spreading causes some loss of spatial resolution in X-ray images, especially for thicker screens, and the screen thickness must therefore be chosen to reach a compromise between resolution and sensitivity.
Nuclear emulsions
In order to enable visualization of single particle tracks, nuclear emulsions are generally made much thicker than ordinary photographic emulsions (up to 500 micrometres) and they have an even higher silver halide content. Special development procedures can reveal the tracks of individual charged particles or fast electrons as a nearly continuous trail of developed silver grains that is visible under a microscope. If the particle is stopped in the emulsion, the length of its track can be measured to give its range and therefore an estimate of its initial energy. The density of the grains along the track is proportional to the dE/dx of the particle, and therefore some distinction can be made between particles of different type.
Film badge dosimeters
Small packets of photographic emulsions are routinely used by workers to monitor radiation exposure. The density of the developed film can be compared with that of an identical film exposed to a known radiation dose. In this way, variations that result from differences in film properties or development procedures are canceled out. When used to monitor exposure to low-energy radiation such as X rays or gamma rays, emulsions tend to overrespond owing to the rapid rise of the photoelectric cross section of silver at these energies. To reduce this deviation, the film is often wrapped in a thin metallic foil to absorb some of the low-energy photons before they reach the emulsion.
One of the drawbacks of photographic film is the limited dynamic range between underexposure and overexposure. In order to extend this range, the holder that contains the film badge often is fitted with a set of small metallic filters that cover selected regions of the film. By making the filters of differing thickness, the linear region under each filter corresponds to a different range of exposure, and the effective dynamic range of the film is extended. The filters also help to separate exposures to weakly penetrating radiations (such as beta particles) from those due to more penetrating radiations (such as gamma rays).
Thermoluminescent materials
Another technique commonly applied in personnel monitoring is the use of thermoluminescent dosimeters (TLDs). This technique is based on the use of crystalline materials in which ionizing radiation creates electron-hole pairs (see below Active detectors: Semiconductor detectors). In this case, however, traps for these charges are intentionally created through the addition of a dopant (impurity) or the special processing of the material. The object is to create conditions in which many of the electrons and holes formed by the incident radiation are quickly captured and immobilized. During the period of exposure to the radiation, a growing population of trapped charges accumulates in the material. The trap depth is the minimum energy that is required to free a charge from the trap. It is chosen to be large enough so that the rate of detrapping is very low at room temperature. Thus, if the exposure is carried out at ordinary temperatures, the trapped charge is more or less permanently stored.
After the exposure, the amount of trapped charge is quantified by measuring the amount of light that is emitted while the temperature of the crystal is raised. The applied thermal energy causes rapid release of the charges. A liberated electron can then recombine with a remaining trapped hole, emitting energy in the process. In TLD materials, this energy appears as a photon in the visible part of the electromagnetic spectrum. Alternatively, a liberated hole can recombine with a remaining trapped electron to generate a similar photon. The total intensity of emitted light can be measured using a photomultiplier tube and is proportional to the original population of trapped charges. This is in turn proportional to the radiation dose accumulated over the exposure period.
The readout process effectively empties all the traps, and the charges thus are erased from the material so that it can be recycled for repeated use. One of the commonly used TLD materials is lithium fluoride, in which the traps are sufficiently deep to prevent fading, or loss of the trapped charge over extended periods of time. The elemental composition of lithium fluoride is of similar atomic number to that of tissue, so that energy absorbed from gamma rays matches that of tissue over wide energy ranges.
Memory phosphors
A memory phosphor consists of a thin layer of material with properties that resemble those of TLD crystals in the sense that charges created by incident radiation remain trapped for an indefinite period of time. The material is formed as a screen covering a substantial area so that it can be applied as an X-ray image detector. These screens can then be used as an alternative to radiographic films in X-ray radiography.
The incident X rays build up a pattern of trapped charges over the surface of the screen during the exposure period. As in a TLD, the screen is then read out through the light that is generated by liberating these charges. The energy needed to detrap the stored charges is supplied in this case by stimulating the crystal with intense light from a laser beam rather than by heating. The luminescence from the memory phosphor can be distinguished from the laser light by its different wavelength. If the amount of this luminescence is measured as the laser beam scans across the surface of the screen, the spatial pattern of the trapped charges is thereby recorded. This pattern corresponds to the X-ray image recorded during the exposure. Like TLDs, memory phosphors have the advantage that the trapped charges are erased during readout, and the screen can be reused many times.