Aerodynamics

Regardless of the design, a kite must conform to the laws of aerodynamics and embody three fundamental characteristics: an aerodynamic structure to gain lift from the wind, a tether to keep it from blowing away, and a bridle to direct the kite face at the proper angle to the wind. A bridle consists of two or more lines attached directly to the kite face. The bridle lines are connected to each other, forming a tow point adjustable for the prevailing wind conditions. One end of the tether is connected to the tow point, and the other end is most often attached to a hand-held reel in order to manage the flying line efficiently. Some kite designs do away with bridles altogether by having their tethers connected directly to a fixed fulcrum point along the mast or to a keel (as with the delta kite) or series of fins (as with the parafoil) attached perpendicularly to the lifting surface. Locating a kite’s precise fulcrum, or tow point, allows successful flight.

Three main forces control kite flight: lift, gravity, and drag. A kite flies because the lifting force of the wind overcomes both the downward pull of gravity and air resistance to the forward motion of the kite called drag. When tethered and fixed in a position to gain lift from the wind, a kite maintains a perpetual stall—a poor aerodynamic design for an airplane but essential for a kite flying at a stable and positive angle with respect to the horizon.

Flat kites require a tail for drag, which keeps the nose up and creates balance, much like a raft needs a rudder for directional stability. Bowed kites with a bowline strung across the back do not require a tail, since the face takes on a curve, or dihedral angle, which acts much like the bowed hull of a sailboat utilized for self-correcting buoyancy. The box, compound, sled, delta, parafoil, and rotor are inherently stable and typically do not require tails.

Launching and kite safety

Running with a kite is not a good way to launch it. Instead, one should opt for a high start launch, in which one flyer stands about 100 feet (30 metres) downwind, with the kite facing bridle-side to the other flyer, who holds the end of the kite’s line. With a steady breeze behind, a small amount of tension placed on the line allows the kite to rise effortlessly upward. A kite may also be self-launched by letting the kite fly from the flyer’s hand as it takes out line.

The potential hazards of kite flying should be taken seriously. Metals should never be used in the kite line, and kites should be flown in wide-open spaces. Care should be taken to avoid flying in stormy weather or near power lines, public streets, areas congested with people, highways, or airports. Finally, protective gloves should be worn to prevent serious line burn when flying hard-pulling kites.

Modern kite sports

After World War II several new generic kite forms rekindled interest in kite flying in the West. In 1948 the American aeronautical engineer Francis Rogallo patented a completely flexible kite with no rigid supporting spars, which was the forerunner of the delta kite and modern hang gliding. The sled kite, invented by William Allison, came into being in the 1950s, and the parafoil, invented by Domina Jalbert, was a highly original design created in the 1960s. Flying kites continued as a popular pastime over the next two decades.

During the 1980s kite flying with precision-controlled acrobatic stunt kites became popular. Principally chevron-shaped deltas and flexible ram-air soft designs, stunt kites, flown alone or in multiples—one stacked behind the other—can perform high-speed aerial maneuvers such as figure eights, sharp turns, stops in midair, flying backward, and other complex acrobatics. Stunt kites having two flying lines attached to the bridle are called dual-line control kites. Quad-line kites have four flying lines, which offer more precise control and instant braking action.

High-performance kites, including the stunt variety, are made exclusively of synthetic and space-age materials. Framework spars can be fibreglass rods or tubing materials such as filament-wound epoxy, all-carbon (graphite), aluminum carbon, and wrapped graphite. Sails can be plastic, Mylar, Tyvek, ripstop nylon, or other lightweight laminates. Flying line can be braided Dacron or Spectra fibre, a low-stretch synthetic yarn of great tensile strength, which is used exclusively for power flying.

In the 1990s improved synthetics combined with innovations in kite aerodynamics spawned an emerging generation of maneuverable traction kite “engines” capable of enough pulling power to propel a craft across land, water, snow, or ice—an ancient concept reborn. Pilots must master maneuvering the kite as an airborne sail while simultaneously navigating a moving vehicle such as a land buggy that can reach speeds approaching 50 miles (80 km) per hour. Modern kite traction has also revolutionized polar travel. Quadrifoils—soft, sparless, controllable kites—were used to haul personnel and sleds on self-supported treks in a 1995 Arctic expedition across Greenland and in a 1999 expedition to the South Pole.