Early glider experiments of the Wright brothers
The ability of the Wright brothers to analyze a mechanical problem and move toward a solution was apparent from the outset of their work in aeronautics. The brothers realized that a successful airplane would require wings to generate lift, a propulsion system to move it through the air, and a system to control the craft in flight. Lilienthal, they reasoned, had built wings capable of carrying him in flight, while the builders of self-propelled vehicles were developing lighter and more powerful internal-combustion engines. The final problem to be solved, they concluded, was that of control.
Most aeronautical experimenters up to that time had sought to develop flying machines incorporating a measure of inherent stability, so that the aircraft would tend to fly a straight and level course unless the pilot intervened to change altitude or direction. As experienced cyclists, the Wrights preferred to place complete control of their machine in the hands of the operator. Moreover, aware of the dangers of weight-shifting control (a means of controlling the aircraft by shifting the position of the pilot), the brothers were determined to control their machine through a precise manipulation of the centre of pressure on the wings. After considering various mechanical schemes for obtaining such control, they decided to try to induce a helical twist across the wings in either direction. The resulting increase in lift on one side and decrease on the other would enable the pilot to raise or lower either wing tip at will.
Their first experiments with “wing warping,” as the system would be called, were made with a small biplane kite flown in Dayton in the summer of 1899. Discovering that they could cause the kite to climb, dive, and bank to the right or left at will, the brothers began to design their first full-scale glider using Lilienthal’s data to calculate the amount of wing surface area required to lift the estimated weight of the machine and pilot in a wind of given velocity.
Realizing that Dayton, with its relatively low winds and flat terrain, was not the ideal place to conduct aeronautical experiments, the Wrights requested of the U.S. Weather Bureau (later the National Weather Service) a list of more suitable areas. They selected Kitty Hawk, an isolated village on the Outer Banks of North Carolina, which offered high average winds, tall dunes from which to glide, and soft sand for landings.
Tested in October 1900, the first Wright glider was a biplane featuring 165 square feet (15 square metres) of wing area and a forward elevator for pitch control. The glider developed less lift than expected, however, and very few free flights were made with a pilot on board. The brothers flew the glider as a kite, gathering information on the performance of the machine that would be critically important in the design of future aircraft.
Eager to improve on the disappointing performance of their 1900 glider, the Wrights increased the wing area of their next machine to 290 square feet (26 square metres). Establishing their camp at the foot of the Kill Devil Hills, 4 miles (6.5 km) south of Kitty Hawk, the brothers completed 50 to 100 glides in July and August of 1901. As in 1900, Wilbur made all the glides, the best of which covered nearly 400 feet (120 metres). The 1901 Wright aircraft was an improvement over its predecessor, but it still did not perform as well as their calculations had predicted. Moreover, the experience of 1901 suggested that the problems of control were not fully resolved.
Discouraged, but determined to preserve a record of their aeronautical work to date, Wilbur accepted Chanute’s invitation to address the prestigious Western Society of Engineers. Wilbur’s talk was delivered in Chicago on September 18, 1901, and was published as “Some Aeronautical Experiments” in the journal of the society. It indicated the extent to which the Wright brothers, in spite of their disappointments, had already moved beyond other flying machine experimenters.
Solving the problems of lift and control
Realizing that the failure of their gliders to match calculated performance was the result of errors in the experimental data published by their predecessors, the Wrights constructed a small wind tunnel with which to gather their own information on the behaviour in an airstream of model wings of various shapes and sizes. The brilliance of the Wright brothers, their ability to visualize the behaviour of a machine that had yet to be constructed, was seldom more apparent than in the design of their wind-tunnel balances, the instruments mounted inside the tunnel that actually measured the forces operating on the model wings. During the fall and early winter of 1901 the Wrights tested between 100 and 200 wing designs in their wind tunnel, gathering information on the relative efficiencies of various airfoils and determining the effect of different wing shapes, tip designs, and gap sizes between the two wings of a biplane.
With the results of the wind-tunnel tests in hand, the brothers began work on their third full-scale glider. They tested the machine at the Kill Devil Hills camp in September and October of 1902. It performed exactly as the design calculations predicted. For the first time, the brothers shared the flying duties, completing 700–1,000 flights, covering distances up to 622.5 feet (189.75 metres), and remaining in the air for as long as 26 seconds. In addition to gaining significant experience in the air, the Wrights were able to complete their control system by adding a movable rudder linked to the wing-warping system. (See Wright glider of 1902.)