Seismographs and accelerometers

Seismographs are used to measure ground motion in both earthquakes and microseisms (small oscillations described below). Most of these instruments are of the pendulum type. Early mechanical seismographs had a pendulum of large mass (up to several tons) and produced seismograms by scratching a line on smoked paper on a rotating drum. In later instruments, seismograms were recorded by means of a ray of light from the mirror of a galvanometer through which passed an electric current generated by electromagnetic induction when the pendulum of the seismograph moved. Technological developments in electronics have given rise to higher-precision pendulum seismometers and sensors of ground motion. In these instruments the electric voltages produced by motions of the pendulum or the equivalent are passed through electronic circuitry to amplify and digitize the ground motion for more exact readings.

Generally speaking, seismographs are divided into three types: short-period, long- (or intermediate-) period, and ultralong-period, or broadband, instruments. Short-period instruments are used to record P and S body waves with high magnification of the ground motion. For this purpose, the seismograph response is shaped to peak at a period of about one second or less. The intermediate-period instruments of the type used by the World-Wide Standardized Seismographic Network (described in the section Earthquake observatories) had a response maximum at about 20 seconds. Recently, in order to provide as much flexibility as possible for research work, the trend has been toward the operation of very broadband seismographs with digital representation of the signals. This is usually accomplished with very long-period pendulums and electronic amplifiers that pass signals in the band between 0.005 and 50 hertz.

When seismic waves close to their source are to be recorded, special design criteria are needed. Instrument sensitivity must ensure that the largest ground movements can be recorded without exceeding the upper scale limit of the device. For most seismological and engineering purposes the wave frequencies that must be recorded are higher than 1 hertz, and so the pendulum or its equivalent can be small. For this reason accelerometers that measure the rate at which the ground velocity is changing have an advantage for strong-motion recording. Integration is then performed to estimate ground velocity and displacement. The ground accelerations to be registered range up to two times that of gravity. Recording such accelerations can be accomplished mechanically with short torsion suspensions or force-balance mass-spring systems.

Because many strong-motion instruments need to be placed at unattended sites in ordinary buildings for periods of months or years before a strong earthquake occurs, they usually record only when a trigger mechanism is actuated with the onset of ground motion. Solid-state memories are now used, particularly with digital recording instruments, making it possible to preserve the first few seconds before the trigger starts the permanent recording and to store digitized signals on magnetic cassette tape or on a memory chip. In past design absolute timing was not provided on strong-motion records but only accurate relative time marks; the present trend, however, is to provide Universal Time (the local mean time of the prime meridian) by means of special radio receivers, small crystal clocks, or GPS (global positioning system) receivers from satellite clocks.

The prediction of strong ground motion and response of engineered structures in earthquakes depends critically on measurements of the spatial variability of earthquake intensities near the seismic wave source. In an effort to secure such measurements, special arrays of strong-motion seismographs have been installed in areas of high seismicity around the world. Large-aperture seismic arrays (linear dimensions on the order of 1 to 10 km, or 0.6 to 6 miles) of strong-motion accelerometers can now be used to improve estimations of speed, direction of propagation, and types of seismic wave components. Particularly important for full understanding of seismic wave patterns at the ground surface is measurement of the variation of wave motion with depth. To aid in this effort, special digitally recording seismometers have been installed in deep boreholes.

Ocean-bottom measurements

Because 70 percent of the Earth’s surface is covered by water, there is a need for ocean-bottom seismometers to augment the global land-based system of recording stations. Field tests have established the feasibility of extensive long-term recording by instruments on the seafloor. Japan already has a semipermanent seismograph system of this type that was placed on the seafloor off the Pacific coast of central Honshu in 1978 by means of a cable.

Because of the mechanical difficulties of maintaining permanent ocean-bottom instrumentation, different systems have been considered. They all involve placement of instruments on the bottom of the ocean, though they employ various mechanisms for data transmission. Signals may be transmitted to the ocean surface for retransmission by auxiliary apparatus or transmitted via cable to a shore-based station. Another system is designed to release its recording device automatically, allowing it to float to the surface for later recovery.

The use of ocean-bottom seismographs should yield much-improved global coverage of seismic waves and provide new information on the seismicity of oceanic regions. Ocean-bottom seismographs will enable investigators to determine the details of the crustal structure of the seafloor and, because of the relative thinness of the oceanic crust, should make it possible to collect clear seismic information about the upper mantle. Such systems are also expected to provide new data on plate boundaries, on the origin and propagation of microseisms, and on the nature of ocean-continent margins.

Measuring microseisms

Small ground motions known as microseisms are commonly recorded by seismographs. These weak wave motions are not generated by earthquakes, and they complicate accurate recording of the latter. However, they are of scientific interest because their form is related to the Earth’s surface structure.

Some microseisms have local causes—for example, those due to traffic or machinery or due to local wind effects, storms, and the action of rough surf against an extended steep coast. Another class of microseisms exhibits features that are very similar on records traced at earthquake observatories that are widely separated, including approximately simultaneous occurrence of maximum amplitudes and similar wave frequencies. These microseisms may persist for many hours and have more or less regular periods of about five to eight seconds. The largest amplitudes of such microseisms are on the order of 10⁻³ cm (0.0004 inch) and occur in coastal regions. The amplitudes also depend to some extent on local geologic structure. Some microseisms are produced when large standing water waves are formed far out at sea. The period of this type of microseism is half that of the standing wave.