high-pressure phenomena
- Key People:
- Percy Williams Bridgman
- Related Topics:
- pressure
high-pressure phenomena, changes in physical, chemical, and structural characteristics that matter undergoes when subjected to high pressure. Pressure thus serves as a versatile tool in materials research, and it is especially important in the investigation of the rocks and minerals that form the deep interior of the Earth and other planets.
Pressure, defined as a force applied to an area, is a thermochemical variable that induces physical and chemical changes comparable to the more familiar effects of temperature. Liquid water, for example, transforms to solid ice when cooled to temperatures below 0 °C (32 °F), but ice can also be produced at room temperature by compressing water to pressures roughly 10,000 times above atmospheric pressure. Similarly, water converts to its gaseous form at high temperature or at low pressure.
In spite of the superficial similarity between temperature and pressure, these two variables are fundamentally different in the ways they affect a material’s internal energy. Temperature variations reflect changes in the kinetic energy and thus in the thermodynamic behaviour of vibrating atoms. Increased pressure, on the other hand, alters the energy of atomic bonds by forcing atoms closer together in a smaller volume. Pressure thus serves as a powerful probe of atomic interactions and chemical bonding. Furthermore, pressure is an important tool for synthesizing dense structures, including superhard materials, novel solidified gases and liquids, and mineral-like phases suspected to occur deep within the Earth and other planets.
Numerous units for measuring pressure have been introduced and, at times, are confused in the literature. The atmosphere (atm; approximately 1.034 kilograms per square centimetre [14.7 pounds per square inch], equivalent to the weight of about 760 millimetres [30 inches] of mercury) and the bar (equivalent to one kilogram per square centimetre) are often cited. Coincidently, these units are almost identical (1 bar = 0.987 atm). The pascal, defined as one newton per square metre (1 Pa = 0.00001 bar), is the official SI (Système International d’Unités) unit of pressure. Nevertheless, the pascal has not gained universal acceptance among high-pressure researchers, perhaps because of the awkward necessity of using the gigapascal (1 GPa = 10,000 bars) and terapascal (1 TPa = 10,000,000 bars) in describing high-pressure results.
In everyday experience, greater-than-ambient pressures are encountered in, for example, pressure cookers (about 1.5 atm), pneumatic automobile and truck tires (usually 2 to 3 atm), and steam systems (up to 20 atm). In the context of materials research, however, “high pressure” usually refers to pressures in the range of thousands to millions of atmospheres.
Studies of matter under high pressure are especially important in a planetary context. Objects in the deepest trench of the Pacific Ocean are subjected to about 0.1 GPa (roughly 1,000 atm), equivalent to the pressure beneath a three-kilometre column of rock. The pressure at the centre of the Earth exceeds 300 GPa, and pressures inside the largest planets—Saturn and Jupiter—are estimated to be roughly 2 and 10 TPa, respectively. At the upper extreme, pressures inside stars may exceed 1,000,000,000 TPa.
Producing high pressure
Scientists study materials at high pressure by confining samples in specially designed machines that apply a force to the sample area. Prior to 1900 these studies were conducted in rather crude iron or steel cylinders, usually with relatively inefficient screw seals. Maximum laboratory pressures were limited to about 0.3 GPa, and explosions of the cylinders were a common and sometimes injurious occurrence. Dramatic improvements in high-pressure apparatuses and measuring techniques were introduced by the American physicist Percy Williams Bridgman of Harvard University in Cambridge, Mass. In 1905 Bridgman discovered a method of packing pressurized samples, including gases and liquids, in such a way that the sealing gasket always experienced a higher pressure than the sample under study, thereby confining the sample and reducing the risk of experimental failure. Bridgman not only routinely attained pressures above 30,000 atm, but he also was able to study fluids and other difficult samples.
Large-volume apparatuses
Sustained high pressures and temperatures are now commonly produced in massive presses that focus large forces (up to thousands of tons) through two or more strong anvils to compress a sample. The simplest of these devices, introduced by Bridgman in the 1930s, employs two tapered anvils that squeeze the sample like a vise. Although capable of very high pressures—in excess of 50 GPa in designs with sufficient lateral anvil support—the axial force of the squeezer tends to deform samples into extremely flattened, highly strained disks.
The piston-in-cylinder design, in use for more than a century, incorporates a strong metal or carbide piston that is rammed into a sample-confining cylinder. In principle, the piston can be quite long, so a piston-cylinder design can accommodate a much larger volume of sample than the squeezer, depending on the dimensions of the sample-holding cylinder. These devices are rarely used at pressures above about 10 GPa owing to the likelihood of lateral failure (namely, explosive bursting) of the metal cylinder.
The belt apparatus, invented in 1954 by the scientist Tracy Hall of the General Electric Company for use in the company’s diamond-making program, incorporates features of both opposed-anvil and piston-cylinder designs. Two highly tapered pistonlike anvils compress a sample that is confined in a torus, much like a cylinder open at both ends. Hundreds of belt-type devices are in use worldwide in diamond synthesis.
Many high-pressure researchers now employ split-sphere or multianvil devices, which compress a sample uniformly from all sides. Versions with six anvils that press against the six faces of a cube-shaped sample or with eight anvils that compress an octahedral sample are in widespread use. Unlike the simple squeezer, piston-cylinder, and belt apparatuses, multianvil devices can compress a sample uniformly from all sides, while achieving a pressure range with an upper limit of at least 30 GPa. All these types of high-pressure apparatuses can be fitted with a resistance heater, typically a sample-surrounding cylinder of graphite or another electrically conducting heating element, for studies at temperatures up to 2,000 °C.