- Related Topics:
- industrial ceramics
Solid-state sintering
Like traditional ceramics, advanced ceramics are densified from powders by applying heat—a process known as sintering. Unlike traditional ceramics, however, advanced powders are not bonded by the particle-dissolving action of glassy liquids that appear at high temperatures. Instead, solid-state sintering predominates. In this process, matter from adjacent particles, under the influence of heat and pressure, diffuses to “neck” regions that grow between the particles and ultimately bond the particles together. As the boundaries between grains grow, porosity progressively decreases until, in a final stage, pores close off and are no longer interconnected.
Since no glassy phase is needed in solid-state sintering to bond particles, there is no residual glass at the grain boundaries of the resulting dense ceramic that would degrade its properties. As a result, advanced ceramics have improved properties—e.g., strength or conductivity—over their liquid-sintered traditional counterparts, especially at elevated temperatures.
Nevertheless, while pores located at the grain boundaries can be eliminated by grain boundary diffusion, pores left inside the growing grains are extremely difficult to eliminate, no matter how long the object is sintered. For this reason sintering aids are often used to enhance the sintering of advanced ceramics. In reactive-liquid, or transient-liquid, sintering, a chemical additive produces a temporary liquid that facilitates the initial stages of sintering. The liquid is subsequently evaporated, resorbed by the solid particles, or crystallized into a solid.
Solid-state sintering is also aided by chemical additives. A classic example is the sintering of alumina lamp envelopes for sodium-vapour street lights. The lamp envelope must be able to contain the hot sodium discharge, and at the same time it must be transparent, or at least translucent, to visible light. The necessary refractory properties can be found in alumina, but the material does not sinter to translucency, and residual pores that remain within the grains act to scatter light. With magnesia as a sintering aid, however, alumina sinters to translucency. Apparently, magnesia slows the migration of grain boundaries during sintering. Pores remain on these boundaries and are eliminated by grain boundary diffusion. Extremely low porosities can be achieved.
Pressure-assisted sintering
The sintering processes described above can be assisted by the application of pressure. Pressure increases the driving force for densification, and it also decreases the temperature needed for sintering to as low as half the melting point of the ceramic. Furthermore, shape forming and densification can often be accomplished in a single step. Two popular pressure-assisted sintering methods are followed—hot pressing and hot isostatic pressing (HIP).
In hot pressing a heated single-action or dual-action die press is employed. The material composing or lining the rams and die walls is extremely important, since it must not react with the ceramic being hot-pressed. Unfortunately, complex shapes cannot be processed by hot pressing. Hot isostatic pressing involves immersing the green ceramic in a high-pressure fluid (usually an inert gas such as argon or helium) at elevated temperature. For the applied pressure to squeeze out the residual porosity, the ceramic piece must first be presintered to the closed porosity stage (no open, interconnected pores), or else it must be encapsulated with a viscous coating such as glass. During the “HIPing” process, the high-pressure fluid then presses on the exterior, and residual gases from within the piece bubble out and are eliminated. Preformed complex shapes such as turbine blades, rotors, and stators can be densified by HIP.
Rapid heating
Exotic energy deposition methods also are used in the sintering of advanced ceramics. One reason is that conventional radiant heating is slow, so that ceramic powders lose much of their activity, or sinterability, during heat-up. It is therefore advantageous to heat ceramics to the sintering temperature as rapidly as possible. Two means of rapid heating are plasma sintering and microwave sintering. Plasma sintering takes place in an ionized gas. Energetic ionized particles recombine and deposit large amounts of energy on the surfaces of the ceramic being sintered. Extremely high sintering rates have been achieved with this method. In microwave sintering, electromagnetic radiation at microwave frequencies can penetrate and deposit heat in the interior of a sintering ceramic, thus reversing the usual outside-in temperature gradient seen in conventional radiant heating. A combination of radiant and microwave heating can be used to obtain uniform heating throughout the piece. Unfortunately, neither plasma nor microwave sintering is amenable to complex shapes.