- Also called:
- ground-effect machine, or hovercraft
- Key People:
- Sir Christopher Cockerell
- Related Topics:
- Hovercraft
- peripheral jet
- ram-wing craft
- air-cushion train
- skirt
The basic elements of an air-cushion vehicle are a hull, beneath which a skirt system is attached and on which accommodation for passengers, crew, and freight is built; a propulsion system; and a lift system that feeds air into the plenum chamber below the craft in order to provide a cushion. The propulsion and lift systems can be driven by the same power plant or by separate units. If a common power plant is used, the system is known as an integrated lift-propulsion system. Some early craft had only one airflow generating system, which was used for both lift and propulsion, but optimum efficiency for both requirements was difficult to achieve simultaneously, and separate systems are generally used.
The power-to-weight ratio is as critical at the design stage of an ACV as it is in an aircraft. In the ACV it determines not only the payload and performance of the craft but also the ground clearance between the surface and the skirt. The greater the ground clearance, the more efficiently the propulsion forces available can be used. Theoretical design operating weights are essential for comparison and evaluation purposes, but in practice it has been found that air-cushion vehicles can be overloaded by as much as 100 percent of the design payload and still operate.
To obtain the best power-to-weight-to-strength relationships, structural fabrication of air-cushion vehicles has been based more on aviation than on marine practices. Hull structures are of marine aluminum skin, welded or riveted onto aluminum webs or frames. The enclosed spaces are usually sealed so that the airtight compartments thus formed provide natural buoyancy. More recent craft have aluminum honeycomb paneling separated by frames to provide the basic buoyancy raft, and considerable areas of glass-fibre structure also have been incorporated.
Early craft had a hole located near the centre of the buoyancy raft through which air was fed to the plenum chamber beneath, but the development of skirt and other techniques led to the ducting of fan air to the edge of the raft, where it was fed downward into the plenum chamber in the manner of a peripheral jet.
Skirt arrangements
Skirts themselves have developed from a simple curtain designed to enclose the cushion into complicated geometric shapes that contain the cushion, duct the air, and, in some cases, provide a degree of secondary suspension. The simple curtain was quickly replaced by what is now known as a bag skirt. In the shape of a semicircle, this is fastened around the perimeter of the craft; the lower edge is taken inward and upward and is fastened inboard, below the hull. The inflated skirt forms a semicircular cross section. If air is fed through ducts in the top hull so that it inflates the skirt and then is allowed to escape through holes on the inside edge of the bag into the plenum area, the skirt acts as natural ducting, and by varying the size of the holes it is possible to vary the pressure ratio of bag inflation to plenum pressure.
The problem with bag skirts is that the lowest part of the bag quickly wears away, and the bag itself tears, allowing air to escape and releasing the cushion pressure. In 1965 it was decided to lengthen the bag skirt by suspending a curtain-type skirt from it. But instead of a straightforward curtain arrangement, the skirt was split into small segments, each of which acted independently from the others. This segmented, or finger-type, addition to the basic bag skirt became the version most commonly used because worn segments could be replaced quickly and economically and because the independent action of each finger allowed the whole skirt to conform much more closely to the operating surface beneath, reducing drag and air-cushion losses.
Materials used in the skirts have varied from the original rubberized fabric, through pure rubber and nylon, to a lamination of nylon and a proprietary plastic known as neoprene. Bondings between the different layers have to be especially strong; otherwise the fabric delaminates under the severe conditions of wear and loses its tear resistance.
Power plants
Power plants used for air-cushion vehicles are generally gas-turbine engines; the output shaft is driven by a turbine that is not mechanically connected to the main compressor-turbine assembly. In this way the engine can be independent of the fan or propeller that it drives, and the free turbine will not begin to rotate until gas from the engine is allowed to pass over its vanes. This allows the craft to remain stationary and on the ground until the driver decides to move, even though the engines are delivering power. The fans used to provide air pressure for lift are usually of the centrifugal type, in which air is fed in through the centre and driven out at considerably higher pressure around the circumference. Propellers are generally similar to those used for aircraft, although, because the air-cushion vehicles travel in the 0–60-knot speed range and can move in reverse, a standard aircraft propeller designed to operate best at higher speeds is inefficient. Hovercraft propellers can be fixed or mounted on swiveling pylons, which allow the craft to be maneuvered quite accurately, independently of the rudders on which fixed propellers rely. Rudder effectiveness depends to some extent on the forward speed of the craft, and at very low speeds rudders are not efficient as a means of turning.
Other propulsion methods that have been tried in the past include ducted fans, which are quieter than normal propellers but tend to be large and cumbersome. Sidewall craft can be propelled by water screws or by water jets.