- Related Topics:
- lock
- lock gate
- mitre gate
- towpath
- barge
On canalized rivers and artificial canals, the waterway consists of a series of level steps formed by impounding barriers through which vessels pass by a navigation lock. Basically, this device consists of a rectangular chamber with fixed sides, movable ends, and facilities for filling and emptying: when a lock is filled to the level of the upper pound, the upstream gates are opened for vessels to pass; after closing the upstream gates, water is drawn out until the lock level is again even with the lower pound, and the downstream gates are opened. Filling or emptying of the chamber is effected by manually or mechanically operated sluices. In small canals these may be on the gates, but on larger canals they are on culverts incorporated in the lock structure, with openings into the chamber through the sidewalls or floor. While the sizes of the culverts and openings govern the speed of filling or emptying the chamber, the number and location of the openings determine the extent of the water disturbance in the chamber: the design must be directed toward obtaining a maximum speed of operation with minimum turbulence. The dimensions of the chamber are determined by the size of vessels using, or likely to use, the waterway. Where the traffic is dense, duplicate or multiple chambers may be required; in long chambers, intermediate gates allow individual vessels to be passed.
Lock dimensions vary from the small, narrow canal locks of England, with chambers 22 metres (72 feet) long and 2 metres (7 feet) wide, to the 1,500-ton-capacity waterways of Europe, with chambers 198 by 12 metres (650 by 40 feet). On the St. Lawrence Seaway the dimensions are approximately 244 by 24 metres (800 by 80 feet). The lock chambers of the Panama Canal, which are the limiting factor for the size of the vessels that can use this economically important passage, are 300 metres (1,000 feet) long, 33 metres (110 feet) wide, and 12 metres (40 feet) deep.
On canalized rivers the present trend is for locks to be deeper, particularly where they form an integral part of a hydroelectric dam. On the Rhône the lock at Donzère-Mondragon has a depth of 24 metres (80 feet). In Portugal, where the Douro River was developed in the early 1970s for power and navigation, the Carrapatelo Lock has a depth of 35 metres (114 feet).
On artificial canals, where conservation of water is essential, depths do not normally exceed 6 metres (20 feet): water consumption can be reduced by the provision of side pounds either adjacent to the lock, as at Bamberg on the Rhine-Main-Danube waterway, or incorporated in the lock walls, as in the (1899) Henrichenburg Lock on the Dortmund-Ems Canal.
Locks are located to provide good approach channels free from restrictions on sight or movement. Where traffic is heavy or push tows operate, adequate approach walls are needed both to accommodate vessels awaiting entry and to provide shelter from river currents while vessels move slowly into or out of the lock.
Lock gates
Movable gates must be strong enough to withstand the water pressure arising from the level difference between adjacent pounds. The most generally used are mitre gates consisting of two leaves, the combined lengths of which exceed the lock width by about 10 percent. When opened, the leaves are housed in lock wall recesses. When closed, after turning through about 60°, they meet on the lock axis in a V shape with its point upstream. Mitre gates can be operated only after water levels on each side have been equalized.
On small canals, gates may be manually operated by a lever arm extending over the lock side. On large canals, hydraulic, mechanical, or electrical power is used. On the Weaver Navigations Canal in England the hydraulic power for operating the lock gates has been derived for 100 years from the 3-metre (10-foot) head difference between the pounds.
Vertical gates, counterweighted and lifted by winch or other gearing mounted on an overhead gantry, can operate against water pressure; as the gate leaves the sill, water enters the chamber, supplementing or replacing the culvert supply. The turbulence is more difficult to control, and the overhead gantries impose restrictions on masts and other superstructures of a vessel.
The use of sector gates, which turn into recesses in the wall, depends on the physical characteristics of the site and on the traffic using the waterway; falling gates lower into recesses in the forebay, and rolling gates run on rails into deep recesses in the lock walls.
Lock equipment
Ladders recessed into the walls provide access between vessels and the lockside and are vital in case of accidents.
Bollards (mooring posts) on the lockside are used for holding vessels steady by ropes against the turbulence during lock operation; mooring hooks set in recesses in the walls provide an alternative anchorage against surging. Floating bollards are provided in deep locks; retained in wall recesses, they rise or fall with the vessel, obviating the need for continuous adjustment of the ropes. Signals, physical or visual, erected at each end of the lock indicate to approaching craft whether the lock is free for them to enter and, in the multiple-chamber locks, which chamber they should use. Control cabins, centrally situated, enable all operations of the lock gates, sluices, and signals to be carried out by one person from a push-button control panel. Telephone or radio communication between adjacent locks gives advance information enabling the operator to have a lock prepared in anticipation of a vessel’s arrival. Successful experiments in France in the early 1970s were directed toward the automatic passage of a vessel through a flight of locks, the various operations at each lock, once initiated, continuing automatically until the vessel left.
Lock bypasses
The passage of a small pleasure boat through a deep lock is an expensive operation if it is passed alone and can be hazardous if it is passed with large barges that might surge against it. Canoes are normally brought ashore and manually moved around a lock on a portable trolley; larger pleasure craft can be transported on a cradle that is mechanically towed on a lockside rail track.
Water chutes have been introduced in Germany for canoes and rowboats where there are rises of 9 to 24 metres (30 to 80 feet); although more costly to install than a lockside rail track, they are more popular. The canoeist, entering the approach channel, pushes a button actuating the head gates, which rise to allow the water to carry the canoe into and down the chute, where it is kept in the centre of the chute by guide vanes. For upstream passage, canoes are kept afloat by descending water but require manual towage.