Modern control practices.

There are various cases in industrial control practice in which theoretical automatic control methods are not yet sufficiently advanced to design an automatic control system or completely to predict its effects. This situation is true of the very large, highly interconnected systems such as occur in many industrial plants. In this case, operations research (q.v.), a mathematical technique for evaluating possible procedures in a given situation, can be of value.

In determining the actual physical control system to be installed in an industrial plant, the instrumentation or control-system engineer has a wide range of possible equipment and methods to use. He may choose to use a set of analogue-type instruments, those that use a continuously varying physical representation of the signal involved—i.e., a current, a voltage, or an air pressure. Devices built to handle such signals, generally called conventional devices, are capable of receiving only one input signal and delivering one output correction. Hence they are usually considered single-loop systems, and the total control system is built up of a collection of such devices. Analogue-type computers are available that can consider several variables at once for more complex control functions. These are very specific in their applications, however, and thus are not commonly used.

The number of control devices added to an industrial plant may vary widely from plant to plant. They may comprise only a few instruments that are used mainly as indicators of plant-operating conditions. The operator is thus made aware of off-normal conditions and he himself manually adjusts such plant operational devices as valves and speed regulators to maintain control. On the other hand, there may be devices of sufficient quantity and complexity so that nearly all the possible occurrences may be covered by a control-system action ensuring automatic control of any foreseeable failure or upset and thus making possible unattended control of the process.

With the development of very reliable models in the late 1960s, digital computers quickly became popular elements of industrial-plant-control systems. Computers are applied to industrial control problems in three ways: for supervisory or optimizing control; direct digital control; and hierarchy control.

In supervisory or optimizing control the computer operates in an external or secondary capacity, changing the set points in the primary plant-control system either directly or through manual intervention. A chemical process, for example, may take place in a vat the temperature of which is thermostatically regulated. For various reasons, the supervisory control system might intervene to reset the thermostat to a different level. The task of supervisory control is thus to “trim” the plant operation, thereby lowering costs or increasing production. Though the overall potential for gain from supervisory control is sharply limited, a malfunction of the computer cannot adversely affect the plant.

In direct-digital control a single digital computer replaces a group of single-loop analogue controllers. Its greater computational ability makes the substitution possible and also permits the application of more complex advanced-control techniques.

Hierarchy control attempts to apply computers to all the plant-control situations simultaneously. As such, it requires the most advanced computers and most sophisticated automatic-control devices to integrate the plant operation at every level from top-management decision to the movement of a valve.

The advantage offered by the digital computer over the conventional control system described earlier, costs being equal, is that the computer can be programmed readily to carry out a wide variety of separate tasks. In addition, it is fairly easy to change the program so as to carry out a new or revised set of tasks should the nature of the process change or the previously proposed system prove to be inadequate for the proposed task. With digital computers, this can usually be done with no change to the physical equipment of the control system. For the conventional control case, some of the physical hardware apparatus of the control system must be replaced in order to achieve new functions or new implementations of them.

Control systems have become a major component of the automation of production lines in modern factories. Automation began in the late 1940s with the development of the transfer machine, a mechanical device for moving and positioning large objects on a production line (e.g., partly finished automobile engine blocks). These early machines had no feedback control as described above. Instead, manual intervention was required for any final adjustment of position or other corrective action necessary. Because of their large size and cost, long production runs were necessary to justify the use of transfer machines.

The need to reduce the high labour content of manufactured goods, the requirement to handle much smaller production runs, the desire to gain increased accuracy of manufacture, combined with the need for sophisticated tests of the product during manufacture, have resulted in the recent development of computerized production monitors, testing devices, and feedback-controlled production robots. The programmability of the digital computer to handle a wide range of tasks along with the capability of rapid change to a new program has made it invaluable for these purposes. Similarly, the need to compensate for the effect of tool wear and other variations in automatic machining operations has required the institution of a feedback control of tool positioning and cutting rate in place of the formerly used direct mechanical motion. Again, the result is a more accurately finished final product with less chance for tool or manufacturing machine damage.