Basic electronic functions
- Key People:
- Lei Jun
- An Wang
- Robert Morris Page
- Walter Schottky
- Related Topics:
- physics
- industry
- electronic system
- On the Web:
- Society of Photographic Instrumentation Engineers - Introduction to Electronics (Oct. 25, 2024)
News •
Rectification
Rectification, or conversion of alternating current (AC) to direct current (DC), is mentioned in the section The vacuum tube era. A diode, or two-terminal device, is required for this process. Semiconductor diodes consist of a crystal, part of which is n-type and part p-type. The boundary between the two parts is called a p-n junction (see ). As noted above, there is a population of holes on the p-type side of the junction and a population of electrons on the n-type side. If a negative voltage is applied to the p-type side, implying a positive voltage applied to the n-type side, the holes in the p-type region will be attracted away from the p-n junction, as will the electrons on the n-type side. A region on either side of the p-n junction will be depleted of charge carriers, thus becoming effectively an insulator. In this condition, called reverse bias, only a very small leakage current flows.
If these voltages are reversed, however, creating a condition called forward bias, the positive voltage on the p-type side will repel holes across the p-n junction; the negative voltage also will repel the electrons on the n-type side. Both holes and electrons will cross the p-n junction in opposing directions, creating an electric current (see ).
Many details of the motion of holes and electrons have been omitted from this simple description, but the principle seems clear. The p-n junction in a semiconductor diode conducts current with one polarity of applied voltage but not with the other polarity. Typical small diodes will conduct about 0.1 ampere with roughly a 1.5-volt forward bias, and they will withstand 100 or more volts with negligible current flow in the reverse direction. Large industrial diodes can carry up to 5,000 amperes and can block several thousand volts.
Amplification
Using n-p-n transistors
A transistor is constructed with two p-n junctions parallel and very close to one another. A typical configuration is the n-p-n transistor (see ), which has different levels of doping in the two n-type regions and other features that improve its efficiency; in the design shown in the diagram, the n-p-n regions correspond to the source (or emitter), gate (or base), and drain (or collector) of the circuit. In normal operation, such as in an amplifier circuit (see ), there are provisions (batteries in this case) for applying a small forward bias to the base-emitter junction and a larger reverse bias to the base-collector junction. Resistors are arranged in series with each battery to establish steady-state operating conditions, and an AC signal source is contained in the base lead. When the AC signal source is switched off, the battery in the emitter-base circuit causes a small current to flow through the series resistor and the forward-biased emitter-base junction. This results in excess electrons being present in the p-type base region of the transistor. Many more of these electrons are attracted to the collector region by the strong reverse bias on the collector than are attracted to the base connection. In an average n-p-n transistor, more than 100 electrons pass from the emitter to the collector for each 1 that passes from the emitter to the base.
When the AC signal source is switched on, the base current is increased and decreased alternately. The collector current varies in the same way but to a hundredfold larger extent; in effect, the signal has been amplified. The varying collector current through the collector series resistor causes a varying voltage drop, which may be used as the signal source for a subsequent amplifying circuit. This example employs an n-p-n transistor. With a p-n-p transistor, the action is similar except that holes are the primary charge carriers, and the voltages of the batteries and thus the direction of current are reversed.
Using MOSFETs
Another important type of transistor developed by the early 1960s is the field-effect transistor, such as a metal-oxide-semiconductor field-effect transistor, or MOSFET (see ). Another type, the junction field-effect transistor, works in a similar fashion but is much less frequently used. The MOSFET consists of two regions: (1) the source (here shown connected to the silicon substrate) and (2) the drain of one conductivity type embedded in a body of the opposite conductivity type. The space between the source and the drain is covered by a thin layer of silicon dioxide formed by heating the silicon in an oxidizing atmosphere. A third part of the device, the gate, is a thin metal layer deposited on the silicon dioxide.
There are several types of MOSFETs, including an n-channel type, so designated because, when it is in operation, the application of a positive voltage to the gate with respect to the p-type region causes a thin conducting region containing mostly electrons to form in the p-type region just beneath the gate. The gate voltage repels holes and attracts electrons from the p-type region, in which there are some electrons even though the principal charge carriers are holes. The thin layer of electron-rich material, the channel, connects the source and drain electrically and permits current to flow between them when the drain is biased positively with respect to the source. The amount of current is controlled by the gate voltage. Without gate voltage, no current flows, because the p-n junction around the drain region is reverse-biased and because no channel exists. MOSFETs are widely used in integrated circuits.