Mining and concentrating
- Key People:
- Sir Ernest Oppenheimer
- Related Topics:
- gold
- materials processing
News •
The nature of the ore deposit determines the mining and mineral processing techniques applied. Oxide ore deposits are frequently of such low grade (e.g., 3 to 10 parts per million) that extensive mineral processing cannot economically be justified. In this case they are merely shattered by explosives and then piled into heaps for extraction by cyanidation (see below). These heaps can be hundreds of metres long and 15 to 30 metres in height.
Alluvial deposits are either dredged from pond and river bottoms or sluiced from banks and floodplains with high-pressure hydraulic hoses. Alluvial deposits require little or no comminution; they are usually concentrated by gravity techniques such as jigging or tabling, in which a slurry is passed through jigs or over grooved or ridged tables that retain the denser gold particles while allowing the much less dense sand and gravel to pass over.
Endogenetic deposits frequently contain elemental gold that is highly disseminated within a base metal sulfide mineral. These deposits are mined, crushed and ground, and then concentrated first by gravity separation to recover coarse particles of native gold before being subjected to froth flotation to concentrate the sulfide mineral fraction that contains the gold.
Extraction and refining
Amalgamation
Elemental gold (and silver as well) is soluble in mercury, so that, when particles of the metal are brought into contact with a fresh mercury surface, they are wetted and dissolved, forming an alloy called amalgam. This phenomenon is exploited for the recovery and concentration of fine particulate gold or silver.
Amalgamation is accomplished by passing a slurry of ore over copper plates coated with mercury, by mixing a slurry of ore and mercury in a cylindrical or conical vessel called an amalgam barrel, or by grinding the ore in a ball, rod, or pebble mill to free the gold from the mineral matrix and then adding mercury to the mill and continuing grinding until the gold has dissolved in the mercury. The denser amalgam is then separated from the now barren ore in the mill discharge. After filtration and washing to remove impurities, the amalgam is heated in a sealed retort to distill off the mercury, which is recovered for reuse.
Although amalgamation is still practiced extensively in gold recovery, the very real hazards of mercury poisoning of either the operators or the environment have limited its application and compelled the use of carefully designed equipment to ensure against contamination.
Cyanidation
More gold is recovered by cyanidation than by any other process. In cyanidation, metallic gold is oxidized and dissolved in an alkaline cyanide solution. The oxidant employed is atmospheric oxygen, which, in the presence of an aqueous solution of sodium cyanide, causes the dissolution of gold and the formation of sodium cyanoaurite and sodium hydroxide, according to the so-called Elsner reaction: 
When gold dissolution is complete, the gold-bearing solution is separated from the solids.
With ores of higher gold content (i.e., greater than 20 grams of gold per ton of ore), cyanidation is accomplished by vat leaching, which involves holding a slurry of ore and solvent for several hours in large tanks equipped with agitators. For extracting gold from low-grade ores, heap leaching is practiced. The huge heaps described above are sprayed with a dilute solution of sodium cyanide, and this percolates down through the piled ore, dissolving the gold.
Immense amounts of solution and solids are associated with a vat leaching circuit, owing to the very low concentrations of gold in the ores. In order to eliminate the huge capital costs associated with the purchase and installation of solids/liquids separation equipment, techniques have been developed that circumvent the entire separation process. One of these is the addition of granular activated carbon to the ore slurry during or upon completion of gold solubilization. The dissolved gold is readily adsorbed onto the carbon, thus removing it from solution, and the granular carbon is separated from the now barren ore by running the slurry through a screen. Gold is then leached from the carbon particles by a strong solution of sodium cyanide and sodium hydroxide, and it is recovered from solution by electrowinning directly onto steel wool or by the Merrill-Crowe process. In the latter process, the gold-bearing solution is deoxygenated and passed through a filter-press, where the gold is displaced from solution by reduction with zinc metal powder.
Extraction from refractory ores
Many gold-bearing ores and concentrates are not readily amenable to cyanidation, owing to the presence of substances that consume the cyanide reagent before it can dissolve the gold, preferentially adsorb the gold as it dissolves (a phenomenon called preg-robbing), or completely surround the gold particles in such a way as to prevent access by the cyanide leach solution. Such ores are referred to as refractory, and they frequently contain the sulfide minerals pyrite, pyrrhotite, or arsenopyrite. Gold can be freed from these ores or concentrates by treating them with various oxidizing processes. The most common method is to roast gold-bearing minerals at temperatures of 450° to 750° C (840° to 1,380° F) to destroy the interfering sulfides. Oxidation can also be accomplished by the use of high-pressure reactors called autoclaves, in which the minerals in an aqueous slurry are treated at high temperature and pressure with oxygen-bearing gases. After oxidation is complete, cyanidation, as described above, is employed to solubilize and extract the gold.
A large proportion of gold is recovered from refractory ores, and considerable skill is required in the design and operation of such facilities.