Materials of construction
Wood was for many centuries the most important and, in fact, the only shipbuilding material. It is still used for boats and small craft of many types, as it is easily handled and worked by local craftsmen with simple tools. However, it is a relatively weak material and is subject to rapid deterioration. The problem of fastening the timbers together is a critical one, and slippage along fore-and-aft flush seams is difficult to prevent. Large wooden ships had to have diagonal metal straps bolted to the planking to counteract slipping at the seams and to keep the hulls in shape. Others made use of hogging girders or tie rods running over high vertical posts to prevent the ends of the hulls from drooping. Many modern metal ships have wooden weather decks to help insulate the spaces below and to provide a good walking surface.
The development of strong waterproof glues and techniques for building up large curved members from thin laminations has greatly improved the strength and stiffness of wooden ship structures. Checking, splitting, knots, and other imperfections are largely eliminated, and many short pieces can be used. Molded plywood yacht hulls made of five thin layers glued together, with the grain running in different directions, are stiff enough to hold their shape without an internal framework.
The steels most widely used for hull structures are of the medium, high-tensile, and special-treatment types. By far the greatest proportion of parts are of medium steel, where the working strains are small or moderate compared with the yield strain. Both high-tensile and special-treatment steels have higher yield points; the latter has ballistic and shock-resisting properties as well. They are used for parts subjected to high strains in order to save hull weight. Cargo ships have been built entirely of high-tensile steel, with a considerable saving in steel weight.
Investigations in the latter 1940s revealed that many of the fracture casualties of that period were due to the use of steel lacking in notch toughness. This term refers to the steel’s ability to absorb energy by stretching in the vicinity of sharp corners, notches, and cracks, particularly at low temperatures or at high stretching rates. This quality is particularly important where all the plating seams around the girth are welded. Many ship structures have several riveted seams to permit adjustment of the strains due to butt welding and to localize progressive cracking. Specifications for shipbuilding steels of later decades required certain minimum limits on notch toughness and on adaptability to welding.
Aluminum alloys are used for the hulls of patrol boats, small cargo ships, and for large shipboard elevator platforms and similar structures. They are also used for the superstructures and upper works of many cargo and passenger vessels; they form the upper parts of steel hull girders which bend elastically in service. For the last-named purpose, the increased deformation or stretch of these alloys is an advantage. For a given weight, panel plates of aluminum alloy are thicker and stiffer than those of steel. They thus provide a better appearance and for many installations they do not require painting.
Use of aluminum for large ship structures, such as the hull proper, in which appreciable savings in weight are to be achieved, requires reliable welding and riveting in large thicknesses. What is more, it necessitates the acceptance of increased bending deformations along the length and lowered natural frequencies of vibration as compared with similar structures of steel.
Hulls of heavily reinforced concrete have been used for ships and barges in times of emergency, when steel reinforcing rods and labour trained in building construction were available and shipbuilding steel and labour having shipbuilding skills were not.
Plastics reinforced with glass fibre eliminate many of the joints in a boat and greatly decrease the deterioration encountered in wooden or metal hulls. They may be coloured with pigment and they lend themselves admirably to “sticking in” stiffening members and other parts and to repairs in a similar manner when damaged. Many nonstructural parts of boats and ships of all sizes and types are easily fabricated by molding in reinforced plastic.
Jointing, connections, and attachments
It is possible, with fibreglass and similar materials, to make a small-boat hull entirely in one piece. However, as the boat becomes large enough to require a fibreglass deck, this is made separately and attached to the hull. For larger craft, the individual planks and plates have to be joined by gluing, screwing, bolting, riveting, or welding. Flush seams (fore-and-aft joints) and butts (girthwise joints) for smooth external hull surfaces are possible by gluing and welding. Screwing, bolting, riveting, or welding require lapping the members over each other or the use of internal (and external) connecting straps, strips, or other parts. Nailing for small-boat structures of wood is no longer favoured because of the difficulty in making repairs. If the limitations and advantages of each of the jointing methods are kept firmly in mind, it will be found that practically every one of them serves well in some particular application on board ship.
Welding has the great advantage over riveting in that it eliminates excess metal and saves weight practically everywhere in a ship structure, sometimes as much as 10 percent. As a rule, the loads are transmitted from one member to another more directly, and the resulting structure is more rigid. Under heavy deformation, such as collision damage, the welded joints will hold together better than riveted connections. Under mild deformation they are less liable to leak. Welded shell plating is much smoother than riveted plating, with appreciable savings in friction and total resistance. On the other hand, poor welding is often undetected from the outside. One small flaw in an unfortunate position can initiate a major crack.
Structural tests of ships and models
Those who made the early strength calculations of iron ships in the 1850s and 1860s benefited from the studies and tests of Isambard Kingdom Brunel and William Fairbairn on the tubular or box-shaped bridges previously built in Great Britain. Fracture and loss of the fast, light British destroyer HMS Cobra in the early 1900s led to tests of another destroyer, HMS Wolf. The need for information on the behaviour of similar structures when actually loaded to the buckling or fracture point led, in 1930, to full-scale tests of the U.S. destroyers Preston and Bruce and, later, of the British destroyer Albuera. These tests confirmed the use of the simple beam theory for large, thin, box-shaped structures, and indicated the relative effectiveness of stiffened and unstiffened material and the rigidity of riveted joints.
Fractures of welded ship hulls during the early 1940s led to a new series of extensive structural-testing programs by Great Britain and the United States on full-size ships, including tests with various load distributions in calm water.
Beginning with the German MS San Francisco in 1934, a number of ships have been instrumented to determine in heavy seaways the wave profile along the ship’s side, the water pressures and accelerations resulting from ship motion, the deflection of the ship girder, and the simultaneous strains in many parts of the ship structure. The routine collection of measurements of hull stresses on many types of ships has been carried out in the United States, the United Kingdom, Sweden, and elsewhere. Statistical analysis of the data has provided confirmation of methods of predicting long-term stress distributions from model tests and calculations. Ideas regarding these methods and other structural problems are regularly exchanged at meetings of the International Ship and Offshore Structures Congress held every three years.
After the 1920s the techniques of making and testing structural models vastly improved. The availability, after the 1940s, of the wire-resistance strain gauge, with its small size and tiny wires cemented to the metal, made possible the testing and structural analysis of models (and ships) under high-speed dynamic loads such as impacts and shocks from underwater explosions.