Visbreaking, thermal cracking, and coking
- Related Topics:
- cracking
- alkylation
- reforming
- superfractionation
- desulfurization
Since World War II the demand for light products (e.g., gasoline, jet, and diesel fuels) has grown, while the requirement for heavy industrial fuel oils has declined. Furthermore, many of the new sources of crude petroleum (California, Alaska, Venezuela, and Mexico) have yielded heavier crude oils with higher natural yields of residual fuels. As a result, refiners have become even more dependent on the conversion of residue components into lighter oils that can serve as feedstock for catalytic cracking units.
As early as 1920, large volumes of residue were being processed in visbreakers or thermal cracking units. These simple process units basically consist of a large furnace that heats the feedstock to the range of 450 to 500 °C (840 to 930 °F) at an operating pressure of about 10 bars (1 MPa), or about 150 psi. The residence time in the furnace is carefully limited to prevent much of the reaction from taking place and clogging the furnace tubes. The heated feed is then charged to a reaction chamber, which is kept at a pressure high enough to permit cracking of the large molecules but restrict coke formation. From the reaction chamber the process fluid is cooled to inhibit further cracking and then charged to a distillation column for separation into components.
Visbreaking units typically convert about 15 percent of the feedstock to naphtha and diesel oils and produce a lower-viscosity residual fuel. Thermal cracking units provide more severe processing and often convert as much as 50 to 60 percent of the incoming feed to naphtha and light diesel oils.
Coking is severe thermal cracking. The residue feed is heated to about 475 to 520 °C (890 to 970 °F) in a furnace with very low residence time and is discharged into the bottom of a large vessel called a coke drum for extensive and controlled cracking. The cracked lighter product rises to the top of the drum and is drawn off. It is then charged to the product fractionator for separation into naphtha, diesel oils, and heavy gas oils for further processing in the catalytic cracking unit. The heavier product remains and, because of the retained heat, cracks ultimately to coke, a solid carbonaceous substance akin to coal. Once the coke drum is filled with solid coke, it is removed from service and replaced by another coke drum.
Decoking is a routine daily occurrence accomplished by a high-pressure water jet. First the top and bottom heads of the coke drum are removed. Next a hole is drilled in the coke from the top to the bottom of the vessel. Then a rotating stem is lowered through the hole, spraying a water jet sideways. The high-pressure jet cuts the coke into lumps, which fall out the bottom of the drum for subsequent loading into trucks or railcars for shipment to customers. Typically, coke drums operate on 24-hour cycles, filling with coke over one 24-hour period followed by cooling, decoking, and reheating over the next 24 hours. The drilling derricks on top of the coke drums are a notable feature of the refinery skyline.
Cokers produce no liquid residue but yield up to 30 percent coke by weight. Much of the low-sulfur product is employed to produce electrodes for the electrolytic smelting of aluminum. Most lower-quality coke is burned as fuel in admixture with coal. Coker economics usually favour the conversion of residue into light products even if there is no market for the coke.
Purification
Before petroleum products can be marketed, certain impurities must be removed or made less obnoxious. The most common impurities are sulfur compounds such as hydrogen sulfide (H2S) or the mercaptans (“R”SH)—the latter being a series of complex organic compounds having as many as six carbon atoms in the hydrocarbon radical (“R”). Apart from their foul odour, sulfur compounds are technically undesirable. In motor and aviation gasoline they reduce the effectiveness of antiknock additives and interfere with the operation of exhaust-treatment systems. In diesel fuel they cause engine corrosion and complicate exhaust-treatment systems. Also, many major residual and industrial fuel consumers are located in developed areas and are subject to restrictions on sulfurous emissions.
Most crude oils contain small amounts of hydrogen sulfide, but these levels may be increased by the decomposition of heavier sulfur compounds (such as the mercaptans) during refinery processing. The bulk of the hydrogen sulfide is contained in process-unit overhead gases, which are ultimately consumed in the refinery fuel system. In order to minimize noxious emissions, most refinery fuel gases are desulfurized.
Other undesirable components include nitrogen compounds, which poison catalyst systems, and oxygenated compounds, which can lead to colour formation and product instability. The principal treatment processes are outlined below.
Sweetening
Sweetening processes oxidize mercaptans into more innocuous disulfides, which remain in the product fuels. Catalysts assist in the oxidation. The doctor process employs sodium plumbite, a solution of lead oxide in caustic soda, as a catalyst. At one time this inexpensive process was widely practiced, but the necessity of adding elemental sulfur to make the reactions proceed caused an increase in total sulfur content in the product. It has largely been replaced by the copper chloride process, in which the catalyst is a slurry of copper chloride and fuller’s earth. It is applicable to both kerosene and gasoline. The oil is heated and brought into contact with the slurry while being agitated in a stream of air that oxidizes the mercaptans to disulfides. The slurry is then allowed to settle and is separated for reuse. A heater raises the temperature to a point that keeps the water formed in the reaction dissolved in the oil, so that the catalyst remains properly hydrated. After sweetening, the oil is water washed to remove any traces of catalyst and is later dried by passing through a salt filter.