- Related Topics:
- zinc
- materials processing
Zinc ores are widely distributed throughout the world, although more than 40 percent of the world’s output originates in North America and Australia. The common zinc-containing minerals are the zinc sulfide known as zinc blende or sphalerite (ZnS), a ferrous form of zinc blende known as marmatite [(ZnFe)S], and a zinc carbonate known as calamine or smithsonite (ZnCO3).
The geology of zinc deposits is complex. In most cases, hydrothermal mechanisms have occurred in which aqueous solutions were forced through porous strata at high temperatures and pressures to dissolve zinc, lead, and other minerals, which were finally precipitated as sulfides. The zinc content of mined ore is usually between 3 and 10 percent. Almost all ores contain the lead sulfide mineral galena and small quantities of cadmium sulfide. Chalcopyrite, and copper-iron sulfide, is often present. The most common gangue constituents are calcite, dolomite, and quartz.
Mining and concentrating
Zinc ores are recovered by many mining techniques, ranging from open-pit mining (mainly in the case of oxidized ore bodies, which are located closer to Earth’s surface) to the normal underground methods (used for the more deeply located sulfide ores). The most common underground method of ore extraction is cut-and-fill stoping, in which tunnels are dug to moderate depths, branching away from the mine portals.
The small fraction of zinc sulfide minerals present in the ore makes beneficiation necessary in order to produce a concentrate suitable for treatment. The most common method for accomplishing this concentration is to isolate the sulfide mineral from the impure constituents, or gangue, by flotation separation. In this process, the ore initially is crushed to about 1.9 centimetres (0.75 inch), combined with water, and ground to less than 0.1 millimetre in a ball mill. The finely ground particles and water form a slurry that flows from the mill to flotation cells or tanks, where, in the presence of selected chemical reagents that create a suspension of air bubbles, the slurry is agitated by beaters. The mineral particles cling to the bubbles and float to the surface, forming an oily froth that is constantly skimmed, while the gangue is wetted by the action of the chemicals and sinks in the cell. The proper choice of frothing agents makes it possible to separate each constituent mineral of complex lead and zinc sulfides in a concentrated form.
Extraction and refining
Roasting and sintering
Both of the main extraction methods for the production of zinc, electrolysis and smelting, require the prior removal of sulfur in a highly exothermic oxidation reaction:
For the electrolytic production of zinc, the roasting of concentrates is achieved in fluidized-bed roasters, in which finely divided and heated particles of concentrate are suspended in a rising stream of air. The sulfur content can be reduced to less than 0.5 percent, and a high-strength (10 percent) sulfur dioxide gas is forwarded to a sulfuric acid plant. The process is thermally efficient, and the resulting calcine is in the form of small particles that can easily be leached into solution for further treatment.
The process described above becomes difficult to operate if the grade of concentrate falls and particularly if the lead content rises above 3 percent. For this reason, and because a strong, lumpy feed is required, the zinc-lead blast furnace utilizes a sintering process to supply its oxidized feed. Fine concentrates are mixed with crushed returned sinter to give a material containing about 6.5 percent sulfur. This is fed onto a moving grate and fired in an updraft of air, and the sintered cake leaving the machine is broken into a convenient lump size. By virtue of its strength and hardness, sinter is an ideal feed for the blast furnace. A gas containing 7.5 percent sulfur dioxide is passed to a sulfuric acid plant.
Electrolysis
The basic steps in this process include (1) preparation of a zinc sulfate solution by leaching zinc oxide calcines (produced by the roasting of sulfide concentrates) in dilute sulfuric acid, (2) purification of the resulting zinc sulfate solution, and (3) electrolysis of the purified solution.
The theoretical voltage required to deposit zinc from zinc sulfate solution onto a cathode is about twice the voltage necessary to decompose water, so that, in theory, electrolysis should result in the production of hydrogen at the cathode and not the deposition of zinc. When a zinc cathode is used, however, overvoltage prevents the generation of hydrogen, and, hence, zinc is deposited. The hydrogen overvoltage depends crucially on the purity of the zinc sulfate electrolyte; the presence of certain impurities at even very low concentrations can cause a drastic lowering of the overvoltage and thus interfere with zinc deposition. For this reason, extreme purification of the electrolyte is a critical necessity in the process and is accomplished in two stages. The first stage is the removal of iron as a solid residue in the form of either jarosite (a basic ferric sulfate) or the oxides goethite or hematite. This is then followed by cementation with zinc dust to remove other metallic impurities (including copper, nickel, cadmium, cobalt, and germanium) from the solution.
Electrolysis is performed in lead-lined concrete cells with anodes of lead containing 0.5–1.0 percent silver and cathodes of aluminum sheet. The zinc deposits are stripped from the cathodes every 24 to 48 hours and remelted in an induction furnace before casting into ingots or pigs. The purification of the electrolyte ensures that the normal product will reach a purity of 99.99 percent or more. In existing plants, outputs vary from 50,000 to 300,000 tons per annum.