Transfer of sediment from source basins to depositional sites on a fan surface involves flow consisting of several types, ranging from high-viscosity debris or mudflows to flows involving normal water. The type of flow experienced on any fan depends primarily on the geologic characteristics of the basin and on the magnitude of precipitation that initiates the flow event. In arid regions the ephemeral nature of rivers and the character of rainfall results in spasmodic rather than continuous deposition on the fan surface. The location of deposition tends to change repeatedly. Deposits of any single flow usually are confined to shallow channels and because of this assume a long, linear distribution. Each deposit may be up to several kilometres long and only 100 to 700 metres wide. The dimensions of each deposit depend on the viscosity of flow, the permeability of surface material, and how far down the fan flow can be held within a distinct channel. Although flow emerging onto the fan surface follows well-defined channels near the apex, water overflows the banks and spreads outward as diffuse flow at some point along the down-fan path of movement. Where the channel is capable of shifting laterally, the location of deposition tends to develop a sheet of rather poorly bedded sand and gravel in which individual layers can be traced for some distance away from the channel. Commonly these sheets are interrupted by thick deposits that represent entrenchment and backfill into the fan surface.

Debris flows or mudflows must follow well-defined channels because a greater depth of flow is needed to offset the high viscosity of the fluid. Nonetheless, debris flows may overflow banks and spread out as sheets, though their viscosity suggests that they will not spread as far laterally as normal water flows. Debris flows are so dense that they are capable of transporting large boulders for considerable distances. The distance of transport, however, is limited by the high viscosity of the fluid, and so movement down the channel may simply stop, even though the fluid is still confined within the channel. Fan deposits that result from debris flows are characteristically unsorted, having clast sizes that range from clay to boulders. Usually no sedimentary structures such as bed forms or cross-beds are observed in deposits of this type. Also, the deposits of debris flows are usually lobate and have well-defined margins often marked by distinct ridges. Some fans are built almost entirely by debris flows. The flow characteristics seem to be generated most commonly in arid or semiarid climates, where torrential rains are separated by periods of little or no precipitation. This pattern allows material to collect on the slopes of the source basin and provides the load necessary to generate a debris-flow pattern.

This does not mean that debris flows are restricted only to those climatic regions. Fans developed primarily by debris-flow action have been described in humid temperate regions, such as New Zealand and Virginia in the United States. In general, fans in Virginia, found on the east flank of the Blue Ridge Mountains, are smaller than arid fans and do not have the same areal relationships as the dry fans in California. They are typically elongate and rather irregular. Such fans probably result from major storm events, which in some cases erode deep trenches near the apex and deposit coarse debris across the lower fan surface. Geologic evidence suggests that the interval between depositional events can be extremely long, some possibly having a depositional recurrence interval from 3,000 to 6,000 years. Therefore, alluvial fans developed by these processes may be extremely old and not necessarily related to the modern climate. This also is demonstrated in some fans in the White Mountains of California, which have been continuously accumulating for more than 700,000 years and appear to be totally composed of debris-flow deposits.

Deposition on true wet fans seems to be considerably different from that associated with dry fans. Fans developed in the Kosi River basin in India contrast drastically with classic dry fans. The Kosi fan has as its source the Himalayas, and sediment derived from that source is being collected in the piedmont area. During the last several hundred years, the Kosi River has shifted approximately 100 kilometres while creating its large wet fan. At the fan apex, sediment is characteristically coarse gravel, which is rarely transported far downstream. The river tends to widen drastically in a downstream direction, and braiding becomes the dominant channel pattern spread over an extremely wide area of the fan—approximately six kilometres. The shift in channel location seems to be a progressive event rather than the almost random shifting noted on dry fans. Fans developed by this perennial flow should have rather well-defined stratification and be very well sorted. Both of these characteristics have been demonstrated by experimental flume studies of wet fans, and such characteristics are occasionally shown in the natural field setting.

Although lateral shifting of modern washes is necessary for the development of some fan characteristics, it is equally important to recognize that the loci of deposition also migrate along radial lines during fan development. Such longitudinal shifting is facilitated by entrenching and/or backfilling the channel that links the source area to the fan. Incision at the fan apex produces a fan-head trench, which has a lower gradient than the fan surface. The trench is thus deepest at the apex and becomes shallower as it progresses down the fan; it eventually becomes part of the normal drainage system on the fan surface. This property is significant because sediment may be transported and deposited farther down fan in the confines of a trench than it would be in a normal surface channel. The location of fan deposition may thus depend on where the trench channel emerges onto the fan surface. Entrenchment near the fan apex can be temporary or permanent. Distinguishing between these two possibilities is critical in an analysis of fan origin, and it often demands an understanding of whether the fan surface is still part of the active system. Many fan-head trenches appear to be short-term features in that they show evidence of alternating episodes of trenching and filling. In that sense, the entrenchment is temporary in nature. Experimental studies of wet fans and field observations have increased scientific perception of how the temporary nature of fan-head trenches is controlled. In wet fans, sediment is spread as a sheet over most of the area near the fan apex. Deposition in the down-fan area, however, occurs in numerous braided channels. This depositional pattern will continue until the fan slope near the apex becomes so steep that it initiates vertical incision by the trunk river. The result of incision is the fan-head trench. Flow becomes confined within that channel rather than being spread evenly across the upper part of the fan. Thus, the fan surface near the apex is temporarily starved of sediment, and most of the water and debris coming from the source area is transported down the fan in the entrenched channel. As entrenchment migrates upstream into the source area, increased load is derived as the trunk river is rejuvenated. The load is subsequently transported downstream and deposited in the fan-head trench. This initiates a phase of deposition within the trench that raises the channel floor until the trench is totally filled, and deposition begins again over the entire apical area. Eventually the gradient becomes over-steepened and the process repeats itself. In this case, it is clear that the fan-head trench is temporary. The entire fan may continue to grow with time, but the apex area experiences episodes of entrenchment during which sediment is reworked and moved farther down the fan. These episodes alternate with filling of the channel until the slope of the fan near the apex is increased to a threshold condition.

Temporary entrenchment may result from processes other than the built-in system described above. It may be that alternating trenching and filling results when fan processes change during variations of climate that produce different amounts of sediment, rainfall, and discharge. In such a case, the primary driving force is external to the system and is involved more with characteristics of the drainage basin than with processes operating at the fan apex.

In some cases, entrenchment on a fan surface is permanent or certainly long-term. Depths of incision are often greater than 30 metres below the fan surface, making trenches of that magnitude very difficult to refill. The cause of incision of this magnitude is usually external to the fan system itself. In basins of deposition that are open, the most common cause of permanent entrenchment is a decline in baselevel by the river flowing through the basin. This will initiate a wave of fan incision that is propagated up the fan from the toe. Eventually the entire fan is dissected when entrenchment reaches the apex and proceeds into the drainage basin. When this occurs, the fan surface standing above the trench is no longer part of the active fan. In fact, soils will develop on the alluvium, and drainage networks will be established on the old fan surface.