The Gutenberg press
Documents of the period, including those relating to a 1439 lawsuit in connection with Gutenberg’s activities at Strassburg, leave scarcely any doubt that the press has been used since the beginning of printing.
Perhaps the printing press was first just a simple adaptation of the binding press, with a fixed, level lower surface (the bed) and a movable, level upper surface (the platen), moved vertically by means of a small bar on a worm screw. The composed type, after being locked by ligatures or screwed tight into a right metal frame (the form), was inked, covered with a sheet of paper to be printed, and then the whole pressed in the vise formed by the two surfaces.
This process was superior to the brushing technique used in wood-block printing in Europe and China because it was possible to obtain a sharp impression and to print both sides of a sheet. Nevertheless, there were deficiencies: it was difficult to pass the leather pad used for inking between the platen and the form; and, since several turns of the screw were necessary to exert the required pressure, the bar had to be removed and replaced several times to raise the platen sufficiently to insert the sheet of paper.
It is generally thought that the printing press acquired its principal functional characteristics very early, probably before 1470. The first of these may have been the mobile bed, either on runners or on a sliding mechanism, that permitted the form to be withdrawn and inked after each sheet was printed.
Next, the single thread of the worm screw was replaced with three or four parallel threads with a sharply inclined pitch so that the platen could be raised by a slight movement of the bar. This resulted in a decrease in the pressure exerted by the platen, which was corrected by breaking up the printing operation so that the form was pushed under the press by the movable bed so that first one half and then the other half of the form was utilized. This was the principle of printing “in two turns,” which would remain in use for three centuries.
Improvements after Gutenberg
Several of the many improvements in the screw printing press over the next 350 years were of significance. About 1550 the wooden screw was replaced by iron. Twenty years later, innovators added a double-hinged chase consisting of a frisket, a piece of parchment cut out to expose only the actual text itself and so to prevent ink spotting the nonprinted areas of the paper, and a tympan, a layer of a soft, thick fabric to improve the regularity of the pressure despite irregularities in the height of the type.
About 1620 Willem Janszoon Blaeu in Amsterdam added a counterweight to the pressure bar in order to make the platen rise automatically; this was the so-called Dutch press, a copy of which was to be the first press introduced into North America, by Stephen Daye at Cambridge, Massachusetts in 1639.
About 1790 an English scientist and inventor, William Nicholson, devised a method of inking using a cylinder covered with leather (later with a composition of gelatin, glue, and molasses), the first introduction of rotary movement into the printing process.
The metal press (1795)
The first all-metal press was constructed in England in about 1795. Some years later a mechanic in the United States built a metal press in which the action of the screw was replaced by that of a series of metal joints. This was the “Columbian,” which was followed by the “Washington” of Samuel Rust, the apogee of the screw press inherited from Gutenberg; its printing capacity was about 250 copies an hour.
Stereotypy and stereography (late 18th century)
An increasing demand for printed matter stimulated the search for greater speed and volume. The concepts of stereotypy and stereography were explored. Stereotypy, used with notable success around 1790 in Paris, consisted in making an impression on text blocks of type in clay or soft metal in order to make lead molds of the whole. The stereotyped plates thus obtained made it economically possible to print the same text on several presses at the same time. The plates left the pieces of type in the form immediately available for further use and thus increased the rate at which they could be recycled.
A variation of stereotypy was the application, after 1848, of galvanoplastic metallization, in which process plates of thin metal lined with a base of lead alloy were made by electrolytic deposition of a coat of copper on a wax mold of the typeform.
Stereography aimed at bypassing the composition of the type in making the mold. Attempts to perfect the old metallographic method of preparing a clay matrix by stamping with dies brought no better results. In 1797 a variation was tried in which sets of copper matrices of each letter were made in large numbers. The matrices were then assembled according to the wording of the text, so that they covered the whole surface of the bottom of a mold in which the lead plate was then cast. Once the cast had been made, the matrices were available for further use.